User manual BEHRINGER DSP1100P

[. . . ] PRO DSP1100P User´s Manual Bedienungsanleitung Version 1. 0 October 1998 E D FEEDBACK DESTROYER ® www. behringer. de 1 EG-Declaration of Conformity Spezielle Studiotechnik GmbH acc. to the Directives 89/336/EWG and 73/23/EWG We, BEHRINGER INTERNATIONAL GmbH Hanns-Martin-Schleyer-Straße 4 D - 47877 Willich Name and address of the manufacturer or the introducer of the product on the market who is established in the EC herewith take the sole responsibility to confirm that the product: FEEDBACK DESTROYER PRO DSP1100P Type designation and, if applicable, Article-No which refers to this declaration, is in accordance with the following standards or standardized documents: x EN 60065 x EN 55020 x EN 55013 x EN 61000-3-2 x EN 61000-3-3 x EN 55022 The following operation conditions and installation arrangements have to be presumed: acc. Nier, President Name, address, date and legally binding signature of the person responsible Willich, 01. 10. 1998 2 SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. [. . . ] In this case the actual settings will be stored directly to the location that corresponds to the controller value. + Attention!Since the store enable mode allows you to access memory locations directly via MIDI, it is possible that stored presets will be replaced or altered if controller #18 messages are sent on the same MIDI channel. The purpose of this mode is to facilitate MIDI backup and restore operations without express confirmation at the FEEDBACK DESTROYER PRO. It is therefore recommended to disable (flag=0) this mode as soon as the intended data transfer has ended. This is done automatically when you switch off the FEEDBACK DESTROYER PRO. On the sixth, and presently the last, page you can access the System Exclusive functions. To the left of this d a number is displayed: - 0 means that no SYSEX data will be sent or accepted. When STORE is pressed the unit will wait for data, this is shown by flashing dots (LEDs) in the display. The MIDI button LED flashes signaling that SYSEX data is being received. Start your sequencer and press STORE on the unit to start the transmission. If you press the IN/OUT key again on the fifth page, the FEEDBACK DESTROYER PRO quits MIDI setup mode. To load these settings again, select 1, press STORE and start your sequencer. You can at all times press any other key to leave the MIDI setup directly. During a bulk dump all audio functions of the FEEDBACK DESTROYER PRO will be deactivated. The full-featured MIDI implementation of the FEEDBACK DESTROYER PRO allows for easily integrating the FEEDBACK DESTROYER PRO into any MIDI system. s MIDI IN Any MIDI data sent to the FEEDBACK DESTROYER PRO (sequencer, MIDI footswitch, etc. ) are received via the MIDI IN jack. For example, if you wish to use the FEEDBACK DESTROYER PRO as an effects device for your guitar rack, you can connect the MIDI IN jack to a MIDI footswitch that allows for selecting program presets. a multi-effects processor), the data sent from the MIDI footswitch can be routed via the FEEDBACK DESTROYER PROs MIDI THRU jack to your multieffects processor. s MIDI THRU The MIDI THRU jack is used to loop through incoming MIDI data, i. e. any control data received at the MIDI IN of the FEEDBACK DESTROYER PRO will be transmitted via the MIDI THRU jack to other MIDI devices/ instruments. s MIDI OUT The MIDI OUT jack allows for transmitting MIDI data that originate from the FEEDBACK DESTROYER PRO. We are currently developing a software editor which will allow for storing single items of the FEEDBACK DESTROYER PRO`s internal data on an external medium. Thus, it will be possible to archive FEEDBACK DESTROYER PRO settings and presets on a computer, sequencer or MIDI data recorder. [. . . ] 36-38 D - 47877 Willich-Münchheide this modification/adaptation shall not be considered a defect in materials or workmanship. The warranty does not cover any such modification/adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty, BEHRINGER INTERNATIONAL shall not be held responsible for any cost resulting from such a modification/adaptation. Free inspections, maintenance/repair work and replacement of parts are expressly excluded from this warranty, in particular if caused by inappropriate use. [. . . ]