User manual BEHRINGER DSP1000P

[. . . ] DSP1000P User´s Manual Bedienungsanleitung Version 1. 0 October 1998 E D VIRTUALIZER PRO ® www. behringer. de 1 EG-Declaration of Conformity INTERNATIONAL GmbH acc. to the Directives 89/336/EWG and 73/23/EWG We, BEHRINGER INTERNATIONAL GmbH Hanns-Martin-Schleyer-Straße 36 - 38 D - 47877 Willich Name and address of the manufacturer or the introducer of the product on the market who is established in the EC herewith take the sole responsibility to confirm that the product: VIRTUALIZER PRO DSP1000P Type designation and, if applicable, Article-No which refers to this declaration, is in accordance with the following standards or standardized documents: x EN 60065 x EN 55020 x EN 55013 x EN 61000-3-2 x EN 61000-3-3 x EN 55022 The following operation conditions and installation arrangements have to be presumed: acc. Nier, President Name, address, date and legally binding signature of the person responsible Willich, 01. 10. 1998 2 SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. [. . . ] Use the ENGINE L and ENGINE R keys to edit the left or right audio channel settings. Of course, you can edit both channels at the same time in COUPLE mode. When entering COUPLE mode, the VIRTUALIZER PRO copies the parameter settings of the channel last activated to the other channel, so that both of them have an identical set of parameter values. Finally, you can also save the changes made to the preset. E 2. 4 Saving programs Use the STORE key to save an edited preset. Whenever youre editing a preset, the display starts flashing to indicate that the edits will be saved only when you confirm them by pressing the STORE key twice. Then you edit the preset as desired using the function keys and the jog wheel. During this process, the flashing STORE key reminds you that the preset settings have been changed but not saved yet. To keep the original preset, use the jog wheel to select another preset that can be overwritten. If you wish to overwrite the original preset, simply press the STORE key twice (after editing) to save all changes you have made. + Whenever you have edited a preset and pressed the STORE key twice, all previous settings in this preset are erased and overwritten with the new parameter values. However, if you wish to keep the original preset, use the jog wheel to select another preset before you press the STORE key a second time. 2. 5 MIDI control Use the MIDI key combination to select the MIDI parameters you wish to adjust. For this purpose, keep the IN/OUT and the STORE keys pressed for about two seconds. The MIDI menu includes five pages which you can select by pressing the IN/OUT key several times. To switch off the MIDI function, simply select the 0 value (displayed as -). The jog wheel selects one of the following four controller modes: 2. OPERATION 17 Dis play 0 1 2 3 Mode No controller data are trans m itted Controller data are rec eived but not transm itted Controller data are trans mitted but not rec eived Controller data are trans mitted and rec eived Tab. 2. 1: Controller settings The fourth page gives you access to the program change setup. Here, too, four modes can be selected with the jog wheel, as follows: Display 0 1 2 3 Mode Program Program Program Program changes changes changes changes are are are are not transmitted received but not transmitted transmitted but not received transmitted and received Tab. 2. 2: Program change settings The fifth page of the MIDI menu shows the store enable flag represented by a capital S in the display. The value 0 disables the reception of controller #28, and therefore protects the user presets from being modified via MIDI. Accordingly, the value 1 enables MIDI controller #28 so that you can modify or replace presets with a remote MIDI device or a sequencer. In this case the actual settings will be stored directly to the location that corresponds to the controller value. + Attention!Since the store enable mode allows you to access memory locations directly via MIDI, it is possible that stored presets will be replaced or altered if controller #28 messages are sent on the same MIDI channel. [. . . ] The product must be returned in its original shipping carton, together with the return authorization number, to the following address: BEHRINGER INTERNATIONAL GmbH Service Department Hanns-Martin-Schleyer-Str. 36-38 D - 47877 Willich-Münchheide this modification/adaptation shall not be considered a defect in materials or workmanship. The warranty does not cover any such modification/adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty, BEHRINGER INTERNATIONAL shall not be held responsible for any cost resulting from such a modification/adaptation. [. . . ]