User manual BEHRINGER DJX700

[. . . ] User Manual PRO MIXER DJX700 Professional 5-Channel DJ Mixer with Multi-FX Processor, BPM Counter and VCA-Control Your purchase of the BEHRINGER PRO MIXER DJX700 has put you at the forefront of today's trends in DJ mixing consoles. Numerous features, such as beat counter, insert loop and digital effects processor, enable you to work in completely new and creative ways. The DJX700 is a mixer for professional use, it is extremely easy to operate and it helps you give free rein to your creativity. Time is tight and if you don't want to be left in the dust, you'd better get moving. [. . . ] When set to linear, the crossfader PRO MIXER DJX700 User Manual engages directly proportionally to the fader's incremental movement. When set to logarithmic, the fader's movement yields higher volume increases as the fader moves farther along its range of motion. The XPQ 3D surround function is a built-in effect that puts the finishing touch to your music and turns every gig into a real experience. The widening of the stereo base makes for a livelier, more transparent sound. You can determine the intensity of the effect by using the SURROUND control [27], while the XPQ ON switch [28] turns the XPQ effect on (the respective LED is lit). XPQ 3D surround effect When no signal is present (or when the signal level is too low), the BPM display shows only dashes. When the signal is present but can not be identified, the display shows 160 BPM and then shows the said dashes. Therefore, "160" BPM is no usable value; rather, it is simply an error message when the signal can not be analyzed. Pushing this button at least three times in sync with the song's tempo results in the calculated tempo appearing in the DISPLAY. When you have limited the tempo of the tracks on both channels with the SYNC LOCK or BEAT ASSIST buttons, the difference in tempo from both channels is illustrated in the form of a nine-character message on the TEMPO DIFFERENCE-LED [24]. The extent of the difference in tempo is indicated by a corresponding swing to the right (signal A is slower) or to the left (signal B is slower). The TIME OFFSET LED [23] below that displays the signal A and B synchronisation. Should the display move to the left or right, the channels are not synchronised. The TEMPO DIFFERENCE and TIME OFFSET displays are only active if the tempi of both channels have been fixed in one of the ways described. Auto BPM counter 2 3 4 5 6 7 ENGLISH 5 6 The built-in digital effects processor of your DJX700 can process the MASTER signal, the input channels' signal or the microphone signal. Use the SOURCE selector [33] to select the signal on which you want to run the effects. The PROGRAM display [34] located below shows the effect presets that can be recalled by turning and then pressing the PROGRAM control . The LEVEL control [36] is used to determine the volume of the effects signal. Various effects are segmented into seven different groups, offering such standard effects as reverb, delay, echo etc. as well as additional filter and combination effects. PRO MIXER DJX700 User Manual ENGLISH Connections Rear panel connectors [42] The DJX700 features an integrated effects loop for the connection of an external effects device. The MONITOR signal is taken at the SEND output and routed, for example, to a reverb processor. Thus, the signal at the SEND connector is identical to the headphones signal and is selected with the MONITOR CUE buttons [16]. [43] The externally processed signal is added to the MASTER output signal via the RETURN connectors. The effect signal volume may only be adjusted at the output control of the effects device itself. [44] The MASTER output is for connecting to an amplifier and can be adjusted with the MASTER fader [18]. [. . . ] Thank you for your cooperation! [3] Free inspections and maintenance/repair work are expressly excluded from this warranty, in particular, if caused by improper handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons, tubes, guitar strings, illuminants and similar parts. [4] Damage/defects caused by the following conditions are not covered by this § 3 Warranty [1] BEHRINGER (BEHRINGER International GmbH including all BEHRINGER subsidiaries, except BEHRINGER Japan) warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one (1) year* from the original date of purchase, in accordance with the warranty regulations described below. If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under § 5, BEHRINGER shall, at its discretion, either replace or repair the product using suitable new or reconditioned parts. In the case that other parts are used which constitute an improvement, BEHRINGER may, at its discretion, charge the customer for the additional cost of these parts. warranty: · improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals; · connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used; · damage/defects caused by force majeure or any other condition that is beyond the control of BEHRINGER. [5] Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty. [6] If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty, the inspection costs are payable by the customer. [2] If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. [7] Products which do not meet the terms of this warranty will be repaired exclusively at the buyer's expense. [. . . ]