User manual BEHRINGER DJX400

[. . . ] DJX400 Users Manual Version 1. 0 August 2002 PRO MIXER www. behringer. com ENGLISH PRO MIXER DJX400 SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: All the safety and operation instructions should be read before the device is operated. Retain Instructions: The safety and operating instructions should be retained for future reference. Heed Warnings: All warnings on the device and in the operating instructions should be adhered to. Follow instructions: All operation and user instructions should be followed. [. . . ] That could either be the two input channels (CH-1 and CH-2 pressed) or one input signal and the MASTER signal (CH-1 or CH-2 and MASTER pressed). All three signals, however, cannot be simultaneously routed to the headphones; if this were to Never connect devices with line level to the highly sensitive phono inputs!The output level of phono pick-up systems is measured in millivolts, whereas CD players and tape decks have levels measured in volts, i. e. the level from line signals is up to 100 times higher than that of the phono inputs. You select the input signals with the INPUT SELECTOR switch (PHONO/CD). A special feature allows you to switch the input sensitivity of the phono input to line-level, giving the phono connector flexibility (see ). 2. CONTROL ELEMENTS 5 PRO MIXER DJX400 happen, the MASTER signal is the only one that would be heard. The MASTER signal is taken post MASTER LEVEL control, whereas the signals from the two input channels are pre CHANNEL faders and are routed to the MONITOR section. MONITOR SELECT Headphones output CH-1 CH-2 MASTER L R ON OFF OFF CH-1 "L" CH-1 "R" OFF ON OFF CH-2 "L" CH-2 "R" OFF OFF ON MASTER "L" MASTER "R" ON ON OFF CH-1 "L" + CH-2 "L" CH-1 "R" + CH-2 "R" ON OFF ON CH-1 "MONO" MASTER "MONO" OFF ON ON CH-2 "MONO" MASTER "MONO" 2. 6 Front panel connectors Table 2. 1: Selecting a signal with the Monitor Select button 2. 4 MASTER section The LEVEL METER displays the signal level selected with . With this switch you determine whether it is the MASTER or the MONITOR signal to be indicated on the LEVEL METER. When the MONITOR LED lights up, it indicates the level of the headphones signal. Fig. Several tempo changes in one track would produce a constant display of various BPM values and thus lead to unnecessary confusion. Thats why the beat counter sections each have a SYNC LOCK button that can be used during the song to limit the range of possible tempo values. This makes sense if the counter has already calculated a realistic value. Pushing this button manually with the BEAT ASSIST button at least three times in sync with the songs tempo results in the calculated tempo appearing in the DISPLAY. When you have limited the tempo of the tracks on both channels with the SYNC LOCK or BEAT ASSIST buttons, the difference in tempo from channel 1 and channel 2 is illustrated in the form of a nine-character message on the TEMPO DIFFERENCE-LED . The extent of the difference in tempo is indicated by a corresponding swing to the right (the channel 1 signal is slower) or to the left (the channel 2 signal is slower). The TIME OFFSET LED below that displays the channel 1 and 2 synchronisation. Should the display move to the left or right, either channel 1 or channel 2 is not synchronised. The TEMPO DIFFERENCE and TIME OFFSET displays are only active if the tempi of both channels have been fixed in one of the ways described. 6 2. CONTROL ELEMENTS PRO MIXER DJX400 To exit the SYNC LOCK or BEAT ASSIST modes, simply push the SYNC LOCK button once more on both channels. To be sure, slide all the faders to the bottom and switch all controls to the zero position. Using the TAPE output you can record your music by connecting devices such as tape decks, DAT recorders etc. [. . . ] Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by BEHRINGER. Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice. Any product deemed eligible for repair or replacement by BEHRINGER under the terms of this warranty will be repaired or replaced within 30 days of receipt of the product at BEHRINGER. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. [. . . ]