User manual BEHRINGER DI20

[. . . ] The output impedance is balanced and always very low, whereby the signal is far less prone to being affected by noise. + To prevent damaging your loudspeakers, first connect the DI-box and then hook up the respective channel. The same goes for alternating between battery and phantom power operating modes. 2 ULTRA-DI DI20 1. 1 IN input is used to connect unbalanced as well as balanced signal sources to channel 1. CH. 2 IN input is used to connect unbalanced as well as balanced signal sources to channel 2. [. . . ] The signal is fed unbalanced to a guitar amp and balanced to a mixing console (LINK mode). This application has advantages when used with bass guitars, because very few microphones are able to pick up low frequencies at high levels. 2. 2 Converting output signals of a keyboard, DJ-mixer, etc. Fig. CONNECTION OPTIONS 5 ULTRA-DI DI20 This configuration is recommended when using a DJ-mixer or another signal source, which sends an unbalanced line level signal. In addition, if you need a separate monitor signal, the line level signal can be sent to another amplifier. 3. AUDIO CONNECTIONS The BEHRINGER ULTRA-DI DI20 features electronically servobalanced standard inputs and outputs. The circuit design is equipped with automatic hum suppression for balanced signals and operates problem-free even at high levels. The servo function automatically detects unbalanced pin connections and changes the nominal level internally by 6 dB so that there is no difference in level between input and output signals. Fig. MULTILINGUAL DOCUMENTATION + The following versions of this users manual can be downloaded free of charge at http://www. behringer. com: German, French, Spanish, Italian, Dutch, Finnish, Swedish, Danish, Portuguese and Greek. 5. SPECIFICATIONS Frequency response Noise Distortion Input resistance Connection impedance Input Output Max. input level Phantom power Battery power Dimensions Weight 10 Hz to 70 kHz (-3 dB) 100 dBu < 0. 014% (1 kHz, 0 dBu in) > 250 k > 600 1/4" mono jack XLR balanced +12/+32/+52 dBu 18 V DC to 48 V DC 9 V 6LR91 6" (150 mm) x 5" (130 mm) x 2 3/8" (60 mm) approx. 650 g BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those listed or shown. 8 5. WARRANTY § 1 WARRANTY CARD/ONLINE REGISTRATION To be protected by the extended warranty, the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH, in accordance with the conditions stipulated in § 3. Failure to return the card in due time (date as per postmark) will void any extended warranty claims. Based on the conditions herein, the buyer may also choose to use the online registration option via the Internet (www. behringer. com or www. behringer. de). BEHRINGER (BEHRINGER Spezielle Studiotechnik GmbH including all BEHRINGER subsidiaries listed on the enclosed page, except BEHRINGER Japan) warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one (1) year* from the original date of purchase, in accordance with the warranty regulations described below. If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under § 3 and 4, BEHRINGER shall, at its discretion, either replace or repair the product using suitable new or reconditioned parts. In the case that other parts are used which constitute an improvement, BEHRINGER may, at its discretion, charge the customer for the additional cost of these parts. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. Warranty claims other than those indicated above are expressly excluded. To obtain warranty service, the buyer (or his authorized dealer) must call BEHRINGER (see enclosed list) during normal business hours BEFORE returning the product. [. . . ] § 5 WARRANTY TRANSFERABILITY This warranty is extended exclusively to the original buyer (customer of retail dealer) and is not transferable to anyone who may subsequently purchase this product. No other person (retail dealer, etc. ) shall be entitled to give any warranty promise on behalf of BEHRINGER. § 6 CLAIM FOR DAMAGES Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim (consequential) damages. In no event shall the liability of BEHRINGER exceed the invoiced value of the product. [. . . ]