User manual BEGLEC SUPER SOLAR

[. . . ] Virtually no heat production Very low power consumption Lightweight (no lamp transformers needed) This symbol means: indoor use only This symbol means: Read instructions To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages. [. . . ] Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. Check the contents: Check that the carton contains the following items: Operating instructions Super Solar White or Super Solar RGBW Hanging bracket + 2 bolts & 2 nuts This input receives instructions from a DMX-controller or from another Super Solar in master/slave mode. DMX output: 3pin female XLR-connector used to connect the Super Solar White/RGBW with the next unit in the DMX chain or with another Super Solar white/RGBW when used in master/slave mode. Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!Don't cover any ventilation openings as this may result in overheating. The operator has to make sure that the safety-relating and machine-technical installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal. How to set the DIP-switches to obtain the right starting address: Each of the first 9 DIP-switches correspond to a certain DMX-value: DIP #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 OFF = 2CH DMX mode (WHITE-version) Value 1 2 4 8 16 32 64 128 256 OFF = 3CH DMX mode (RGBW-version) ON = 1CH DMX mode You can combine the values of these switches to become any starting address between 1 and 512: Begin address = 01 switch 1=ON values: 1 Begin address = 05 switch 1+3=ON values: 1+4 = 5 Begin address = 09 switch 1+4=ON values: 1+8 = 9 Begin address = 13 switch 1+3+4=ON values: 1+4+8 = 13 . (first DIP switch = ON, all other are OFF) Dipswitch 2 has two functions: OFF: Performs the built-in programs automatically to the rhythm of the music. Eight Chases (dip switch 3 changes the direction of rotation, dip switch 4, 5, 6 changes the speed) 2. Two or more units in master/slave setup: Connect 2 or more units together using good quality balanced XLR microphone cables. [. . . ] Switch off the unit, unplug the mains cable and wait until the unit has been cooled down. During inspection the following points should be checked: All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded. Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation. When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. [. . . ]