User manual BEGLEC LED BALL INDOOR V1.4

[. . . ] (optional CA-8 controller possible) DMX-controlled (4channels: R , G , B + Dimmer/strobe) by any standard DMX-controller. Innovative and extremely quick DMX addressing: Very easy DMX addressing of individual units using any standard DMX-controller Extremely fast DMX addressing of several units at once (automatic address calculation) Ready to use, all cables already connected!To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. [. . . ] The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. Check the contents: Check that the carton contains the following items: Operating instructions LED BALL unit Chain M6 eyebolt Electrical installation for two or more units in DMX-mode: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to "daisy chain" your DMX controller and all the connected units with a good quality balanced cable (ex. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. How to set the DMX addresses: There are 2 ways to set the DMX-address of the units A. Setting individual DMX-addresses per projector: Make sure the DMX cables of all units are connected. Set the DMX-channel, that you want to assign as DMX-start address on you projector, tot maximum (value 255) Press the "Auto DMX address" button (6) on the projector shortly. If you want to set another projector to the same DMX-start address, simply press it's "Auto DMX address" button (6) and it will receive the same address. An example to make things clear: We will set the DMX start address of a projector to 106: Connect the projector to the DMX-controller as described above and make sure all is switched on. Automatic DMX-addressing, starting from any given start address: To save a lot of time (imagine the time it takes to set the DIP switches of 16 units. ) you can set the DMX addresses of all units in the DMX-chain just by the push of a button. No need to calculate the starting address of each individual unit, this will be done for you!Set the DMX-channel, that you want to assign as DMX-start address on you projector, tot maximum (value 255) Press the "Auto DMX address" button (6) on the first projector in the chain for about 5seconds. The first projector in the chain will receive the DMX-start address you chose and it will automatically calculate and program the DMX addresses of all the other units in the DMX-chain!30cm plastic dome Plastic base 230V Mains cable DMX in/output cables with XLR connectors 1m metal chain + metal eyebolt (included) Automatic address button Jack connector for the optional CA-8 controller Pole mount adapter (optional) Wall mount adapter (optional) Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. electrical installation for 1 standalone unit: Just insert the mains cable. The unit starts working immediately in stand-alone mode Remark: You can connect a CA-8 remote controller to the unit if you want to have more control. Electrical installation for two or more units in master/slave: Connect 2 to maximum 16 units together using good quality balanced microphone cables (like for example JB Systems ref. The unit that has no cable connected to its DMX-input will react as "master", the others are the slave units. Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control over the master/slave operation. You can also connect the LEDCON 01 remote controller, in this case all units will respond equally (all units have the same color) An example to make things clear: We want to set the DMX-addresses of 16 units, the DMX start address of the first projector must be 202: Connect all projectors to the DMX-controller as described above and make sure all are switched on. [. . . ] Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. The device should be installed out of reach of people and outside areas where persons may walk by or be seated. Before rigging make sure that the installation area can hold a minimum point load of 10times the device's weight. [. . . ]