User manual BEGLEC IM-7S

[. . . ] Technical Specifications IM-8S Power Fuse Lamp AC 120V~60Hz or AC 230/240/250V 50/60Hz 20mm Glass 10A Fast Blow MSD 250/2 Dimension 360mm x 397mm x 503mm Weight 26 kg IM-7S Power Fuse Lamp AC 120V~60Hz or AC 230/240/250V 50/60Hz 20mm Glass 7A Fast Blow HTI 150W Dimension 373mm x 295mm x 451 mm Weight 13 kg IM-8S IM-7S Innovation , Quality , Performance User Guide WWW. BEGLEC. COM 7. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit's optics. Technical Specification 2. 1 Inserting/Exchanging rotating gobos EC Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. [. . . ] The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp. Always switch off the main supply and never handle the lamp or luminaries when is hot. If this happens, clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation. When burning, the lamp operates at high pressure and there is a slight risk of arc tube rupture. The risk increases with age, temperature and improper handling of the lamp. Make sure the lamp is located in the center of the reflector for the best spot. 7D 5. 5 DMX512 Connection The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. Connect the unit together in a "daisy chain" by XLR plug from the output of the unit to the input of the next unit. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system. The DMX output and input connectors are pass-through to maintain the DMX circuit, when IM-8S power is disconnected to the unit. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). The end of the DMX512 system should be terminated to reduce signal errors. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) IM-7S 5. 4 DMX512 Configuration 4. How To Set The Unit 4. 1 Control Panel Display To show the various menus and the selected functions . LED 8D DMX MASTER SLAVE SOUND Button MENU DOWN UP ENTER Remote controller input By connect to the 1/4" microphone jack to control the unit for Stand by, Function and Mode Sensitivity To adjust the sound sensitivity . Automatic switching between DMX function and built-in stand alone programs. MENU 9D 5. 3. 2 DMX Controller An universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Once the address has been selected, press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later. To go back to the functions without any change press the MENU button again. Please refer to the following diagram to address your DMX512 channel for the first 4 units. [. . . ] Or press the ENTER button again return to the mode the MENU button. button and the display will blink. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Pan Inversion Press the MENU button up to when the is showing on the display. [. . . ]