User manual BEGLEC IM-5W

[. . . ] Safety Instruction Please read carefully the instruction, which includes important information about the installation, usage and maintenance. 6. Troubleshooting Following are a few common problems that may occur during operation. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one. [. . . ] · It can be operated by DMX512 control or can be used as an individual unit without a controller. · Consistent DMX channel enable iRock, iShow and iMove to be link together. · Please use a 3 pin XLR cable/plug when connecting units together. · Accurate focusable optics system and ultra smooth stepping motors. · Dimension : 290 x 330 x 380 mm · Weight : 12 kg IM-5S Independent gobo wheel with 14 gobos plus open and blackout, including 10 metal, 1 replaceable gobo, 2 glass and 1 effect gobos with shaking and shutter effect, Independent color wheel with 11 dichroic colors with rainbow effect. IM-5W Independent color wheel with 11 dichroic colors with rainbow effect and independent shutter & dimmer. 6E 5. 4 DMX512 Configuration 2. 1 Beam Angel Ch 1 IM-5S IM-5W Pan Pan Ch 2 Tilt Tilt Ch 3 Shutter/Sharking Shutter Ch 4 Gobo No function Ch 5 Color Color Ch 6 No function Ch 7 Dimmer Stand by Blackout the unit Strobe 1. Gobo / Color sync. strobe 3. Two-light strobe Sound 1 (LED off ) Blackout the unit Strobe 1. Color sync. strobe 3. Two-light strobe X/Y moving show mode Color selection selection ( Show 1 ~ Show 4 ) Please refer to Show mode in 4. 2 Main Function X/Y moving setting 1. Pan position 2. Tilt position 3. Dimmer First set Master unit, then set Slave units' position Position/ Latch (LED fast blinking) X/Y moving show mode Color/Gobo selection 1. Press shortly for color change in 4. 2 Main Function Sound 2 (LED normal blinking) Slow/Sound 3 (LED on) X/Y moving setting 1. Pan position 2. Tilt position First set Master unit, then set Slave units' position Position/ Latch (LED fast blinking) 3. Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. IM-5S Function Mode Stand by ¥ Lamp : ELC 24V 250W 1. Always switch off the main supply and never handle the lamp or luminaries when is hot. If this happens, clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation. Make sure the lamp is located in the center for the best spot. IM-5W Function Mode Sound 1 (LED off ) Sound 2 (LED normal blinking) Slow/Sound 3 (LED on) 5. 3. 1 iSolution Operation Consistent DMX configuration enable iMove to be linked together with iRock and iShow and controlled at the same time. DMX address can be set remotely by iLead controller ( please refer to the user manual of iLead controller ). Automatic switching between DMX function and built-in stand alone programs. 7E Diagram for Lamp changing 5. 3. 2 DMX Controller An universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Once the address has been selected, press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later. To go back to the functions without any change press the MENU button again. If you use please refer to the following diagram to address your DMX512 channel for the first 4 units. No need to calculate the DMX channels of each fixture in the chain. 4. In order to create a great light show, you can set get contrast movement to each other, even if you have two units only. 5. 2 Easy Controller The easy remote control is used only in master/slave mode. By connecting to the 1/4" microphone jack of the first unit, you will find that the remote control on the first unit will control all the other units for Stand by, Strobe/Next and Fast/Slow function. 4. 2 Main Function Display Inversion It is good for you to install the unit on the floor or under ceiling. To go back to the functions press (display inversion), It will automatically store after 8 seconds. [. . . ] Blackout Mode Press the MENU button up to when the is showing on the display. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Led Display Press the MENU button up to when the is showing on the display. [. . . ]