User manual BEGLEC GALAXY LED V1.0

[. . . ] Uses 2 powerful 10 Watt LEDs: Extremely brilliant beams compared to effects with halogen lamps More dynamic effects compared to effects based on halogen lamps Very sharp colored laser-like beams No lamp replacements!Very low power consumption Lightweight (no lamp transformers needed) Excellent built-in programs for wonderful, ever-changing, light shows: Standalone: sound activated with internal mic Master/slave: wonderful synchronized shows DMX: easy control via 1 DMX channel 2 optional remote controllers available: CA-8: wired remote for improved (DMX) master/slave control RF-8 Set: wireless RF-remote for improved (DMX) master/slave control (RF-8SET = RF-8T "transmitter" + RF-8R "receiver") Mains IEC in/outputs for easy linking using optional IEC cables Perfect for different applications: discos, clubs, mobile DJs, . To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. [. . . ] Should there be any, do not use the device and consult your dealer first. Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual. Check the contents: Check that the carton contains the following items: Operating instructions GALAXY unit Mains cable Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. Electrical installation in DMX-mode: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to "daisy chain" your DMX controller and all the connected units with a good quality balanced cable. Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these cables are compatible with balanced audio cables. pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) Pin layout XLR-5pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) ~ Pins4+5 not used. To prevent strange behavior of the light effects, due to interferences, you must use a 90 to 120 terminator at the end of the chain. Each light effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. Hanging bracket with 1 knob to fasten the unit and a mounting hole to fix a mounting hook. Heat sink for the LED: do not cover this part to ensure proper cooling. mains input with IEC socket and integrated fuse holder , connect the supplied mains cable here. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the mains input of the next GALAXY for easier linking. DMX output: 3pin female XLR-connector used to connect the GALAXY with the next unit in the DMX chain. dMX input: 3pin male XLR-connector used to connect universal DMX-cables. DIP switches, to set the DMX-starting address Safety eye, used to attach a safety cable when the unit is rigged, see paragraph "overhead rigging" ¼" jack used to connect an optional CA-8 controller. Din-5pin input, used to connect an optional wireless receiver, named RF-8R. How to set the DIP-switches to obtain the right starting address: Each of the first 9 DIP-switches correspond to a certain DMX-value: DIP #1 #2 #3 #4 #5 #6 #7 #8 Value 1 2 4 8 16 32 64 128 You can combine the values of these switches to become any starting address between 1 and 512: Begin address = 01 switch 1=ON values: 1 Begin address = 05 switch 1+3=ON values: 1+4 = 5 Begin address = 09 switch 1+4=ON values: 1+8 = 9 Begin address = 13 switch 1+3+4=ON values: 1+4+8 = 13 . Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. [. . . ] During inspection the following points should be checked: All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded. Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation. When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected. [. . . ]