User manual BEGLEC DMX512

[. . . ] TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Lamp 4. How To Set The Unit 4. 1 Control Panel 4. 2 Main Function 4. 3 Home Position Adjust 5. How To Control The Unit 5. 1 Master/Slave Built-In Preprogrammed Function 5. 2 Easy Controller 5. 3 iSolution Operation / DMX Controller 5. 4 DMX512 Configuration 5. 5 DMX512 Connection 6. Troubleshooting 7. Fixture Cleaning User Guide WWW. BEGLEC. COM 1- 1. Safety Instruction Please read carefully the instruction, which includes important information about the installation, usage and maintenance. If you sell the unit to another user, be sure that they also receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the unit. [. . . ] To go back to the functions without any change press the MENU button again. 9- Blackout Mode Press the MENU button up to when the blackout) or is shown on the display. Pressing ENTER (yes Display Inversion It is good for you to install the unit on the floor or under ceiling. To go back to the functions press button and the display will blink. Once the mode has been selected, press the (display inversion), It will automatically store after 8 seconds. Or press the ENTER button again return to the mode the MENU button. ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Display normal mode for the fixture putting on the floor. Pan Inversion Press the MENU button up to when the or is shown on the display. Pressing ENTER (normal) Gobo1 focus Adjust Press the MENU button up to when the is blinking on the display. Pressing ENTER Display inversion mode for the fixture fixing under ceiling. button and the display will blink. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Tilt Inversion Press the MENU button up to when the or is shown on the display. Pressing ENTER (normal) button, the unit will focus on tilt 135°, and then the unit will first focus on tilt 45°, pan 0°, pan 90°, pan 180°, pan 270° each time your press ENTER button. Gobo2 focus Adjust Press the MENU button up to when the is blinking on the display. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. Once the position has button and the display will show the number of working hours of the unit. Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again. Reset Press the MENU button up to when the functions press the MENU button again. DMX RESET : Set DMX value of channel 8 and channel 16 to 255, then all channels of the unit will return to their standard home position. Pressing ENTER been selected, press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again, To go back to the main functions without any change after 8 seconds. Focus Adjust Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button up to when the is shown on the display. [. . . ] Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. 3. Connect the unit together in a "daisy chain" by XLR plug from the output of the unit to the input of the next unit. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system. 4. 7. The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is disconnected to the unit. Each lighting unit needs to have an address set to receive the data sent by the controller. [. . . ]