User manual BECKER CASCADE

[. . . ] In order to avoid malfunctions, it is absolutely essential to observe the relevant cable cross-section when using branch connections/cable connectors. In order to avoid short-circuits and any associated risk of fire, cables which have to be cut must be properly insulated. 4 Installation Guide Connection diagram for the navigation system Radio aerial Speedometer/speedometer cable signal GPS antenna Sound system/ loudspeaker GSM antenn Navigation unit Microphone Reverse signal Power supply Connection options are described in detail on Page 24. The connection for a GSM antenna is only provided in devices with a built-in telephone. The power supply must be protected separately by its own fuses. 5 Installation Guide Installation of the GPS antenna G Risk of injury People with pacemakers should avoid proximity to the magnetic antenna and should not carry the antenna on their person, as this may affect the function of the pacemaker. [. . . ] Remove protective strip from top of adhesive tape (2) and stick to the centre of the base plate underside. Remove protective strip from bottom of adhesive tape (2) and stick the antenna and base plate onto the vehicle console beneath the windscreen at the installation position. Connecting a GSM antenna The connection of a GSM antenna is only necessary or possible for devices with a built-in telephone module. As a GSM telephone antenna is already installed in many vehicles, an adapter is supplied with the device (device connection on an FME connector). Connect the adapter lead to the corresponding socket on the rear of the device. You can then connect to the adapter lead either a commercially available telephone antenna or an antenna that is already installed in the vehicle. If the connections do not fit, you will need to use appropriate adapters. 8 Installation Guide Installation of the microphone The microphone should be placed in the vehicle to allow optimal recognition of the speaker's voice. Possible positions in the vehicle for the microphone can be seen in the following diagram. The installation position should be as far away from the loudspeakers, and as near to the speaker, as possible. In order to pick up as little background noise as possible, the microphone has a narrow pick-up angle and must consequently be directed towards the driver. A: B: C: D: E: F: Optimal installation position Alternative installation position Speaking direction on microphone Adhesive strip for affixing to smooth surfaces Screw for fastening the screw-on plate Screw-on plate for affixing to rough or uneven surfaces. Affixing the hands-free microphone to a flat and smooth surface can be accomplished with the adhesive strip D (Clean adhesion surfaces). 9 Installation Guide If the microphone is to be affixed to a rough or uneven surface, the screw-on plate F should be affixed first with the screw E. (To avoid risk of damage to any cables installed underneath or other vehicle components, please pay attention to screw length. ) Subsequently, affix the microphone to the screw-on plate F with the adhesive strip D. Cable connections for the speed sensor Brown - earth (terminal 31) Black - power supply (terminal 15), 9 - 16V, 30 mA Blue/red - signal for socket A pin 1 Installing the speed sensor in the speedometer cable In this case, please contact your dealer or VDO representative. A GAL signal 15 Installation Guide Installation/ Removal of the Cascade · Installation: The Cascade features an integrated universal bracket for DIN installation slots. The Cascade is inserted into the installation slot and secured with the slides supplied. Subsequently, insert slides into the openings on the front of the Cascade as far as the first detent position (Fig. The installation angle of the Cascade must not exceed 0° - 35° (vertical). To do this, remove the control panel and push in both slides as far as the second detent position as shown in Figure A . Next, remove the slides by pressing the springs on the right and left sides of the Cascade. If the Cascade was previously installed in another vehicle, it may be necessary to adjust the springs on the unit before installationCascade. E (Gently press slide in the direction of 1 while at the same time moving the slide in the direction of 2). A B C D 2 E 1 16 Installation Guide Commissioning and calibration · For commissioning and calibration, you must switch on the vehicle ignition. Switch on the device and enter the code (see the operation guide for a detailed description). The vehicle must be parked outdoors, ensuring that it has a clear view in all directions (not in the immediate vicinity of buildings). [. . . ] The number value behind :KHHO should not increase when the vehicle is in neutral or when the accelerator is pressed while the vehicle is parked. · Engage the reverse gear for the reverse signal function test. · %DFNZDUGV 8008 must jump from to Drive round a bend to test the function of the internal sensors. The value behind *<52 must change. 22 Installation Guide GPS information - GPS function test Select *36 , QIR in the Service menu. [. . . ]