User manual BARTSCHER TF 404 EHP 111447 CONTROL PLAN

[. . . ] 1 Remove all four cartridges from their packaging. Color Tab 7 Remove the protective paper from all four image drums. 2 Shake each cartridge to distribute toner. 5 Lower the right end, then push the blue lock lever forward until it stops. 8 Close the cover. 3 Peel tape off bottom of each cartridge. Setup Guide | 5 6 Load Paper 4 Insert paper and push in the tray. 7 1 Pull out the tray and remove the shipping insert. Connect to Your Computer The printer interface cable is not supplied. PC Systems You need: · A shielded IEEE-1284 parallel bidirectional interface cable, maxiumum length 6 ft. (1. 8 m) Recommended Media Standard paper (Hammermill Laser Print, Radiant White, 24 lb preferred) 1 Plug your interface cable into the parallel port on the back of the printer and secure it with the wire loops. Shipping insert 2 Adjust the paper guides to paper size. Weight: 20 to 28 lb Capacity: Tray holds up to 500 sheets of 20-lb paper ! For details on media and paper paths, see your Handy Reference or Online User's Guide. 2 Plug the other end into your computer and secure it in place with the screws. Macintosh Systems You need: · An BARTSCHERCOLOR 8n model printer, or the optional Okilan 6100e Print Server (P/N 70034201) · A UTP cable with RJ45 connectors If you need to install the Okilan Print Server, see the directions supplied. [. . . ] 2 Attach one end of the UTP cable to the RJ45 port on the printer network server. 3 Attach the other end to the RJ45 port on your Macintosh network card. If you Macintosh does not have an RJ45 port, you will need a network adapter. The Paper Tray Gauge The red paper tray gauge on the front of the tray indicates how much paper is left. 3 Fan paper. ! 6 | BARTSCHERCOLOR 8 8 Connect to Power 10 Install Software Windows 95/98/NT4. 0 1 Insert the BARTSCHERCOLOR 8 CD into your CD drive. 5 Follow the on-screen instructions. 1 Connect the power cord. 2 The outlet must be grounded. Macintosh 9 Print the Demo Page 1 Turn the printer on. 2 Press and hold FORM FEED/Print Demo for 2 seconds. Install the Software: 1 Insert the BARTSCHERCOLOR 8 CD into your CDROM drive. 7 Continue with the installation following the instructions on your screen. Select the Printer: 1 2 Print the BARTSCHERCOLOR 8 menu: press ON LINE on the printer's control panel, then press and hold PAPER SIZE/Print Menu for two seconds until PRINT MENU displays. 2 On the printout, under ETHERTALK, Printer Name, note the name that appears, for example, BARTSCHER_465987. 6 Click Auto Setup to have the Adobe Printer Driver configure your printer automatically OR Click Select PPD to select a PPD file manually. 7 Follow the instructions on your screen to finish. The Demo page prints. Setup Guide | 7 11 Calibrate the Color This is an important process to make sure your BARTSCHERCOLOR 8 gives you sharp, accurate color images. 3 Enter the row number and column letter of the closest matching rectangle into the Column and Row boxes on your screen. This sends the new settings to the printer and prints a color balance verification page. The utility2 to check the color resets the to its default settings each time it prints the test pattern. Macintosh 1 Start the utility: · Windows systems: click Start ® Programs ® BARTSCHERCOLOR 8 ® BARTSCHERCOLOR 8 Color Balance Utility. · Macinstosh systems: in the BARTSCHERCOLOR 8 Macintosh Folder, double-click theColor Balance Utility. Click Reset and Print Adjustment Page to print a color balance adjustment page. Congratulations!Your BARTSCHERCOLOR 8 is ready to print beautiful color documents. 7 Repeat steps 5 and 6 for the remaining eight sections. This time, the box in each section where no color shows should be in the +1, 0, or -1 range for all 9 sections. 9 Click Close. Setup Guide | 9 Control Panel Status Low Toner Indicators *Printer Language Buttons Paper Size Paper Source Buttons The control panel buttons are dual function: press and release to engage the top function; press and hold for 2 to 3 seconds to engage the bottom function. Hold: Prints a Demo Page ! * See the on-line BARTSCHERCOLOR 8 User's Guide on the BARTSCHERCOLOR 8 CD for details on the control panel and printer menus. The printer comes set for Auto Mode (. AUT), which automatically switches between HP PCL5c and Adobe PostScript, depending on the document being processed. 10 | BARTSCHERCOLOR 8 Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. [. . . ] The printer comes set for Auto Mode (. AUT), which automatically switches between HP PCL5c and Adobe PostScript, depending on the document being processed. 10 | BARTSCHERCOLOR 8 Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by Oki Data. [. . . ]