User manual BARTSCHER A300116 CONTROL PLAN

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. As an ENERGY STAR® Program Participant, the manufacturer has determined that this product meets the ENERGY STAR guidelines for energy efficiency. This product complies with the requirements of the Council Directives 89/336/EEC (EMC) and 73/23/EEC (LVD) as amended where applicable on the approximation of the laws of the member states relating to electromagnetic compatibility and low voltage. Oki and Microline are registered trademarks of Oki Electric Industry Company Ltd. ENERGY STAR is a registered trademark of the United States Environmental Protection Agency. [. . . ] · If the software application being used has a collate print option, it must be turned OFF for proof and print to operate correctly. · Proof and print may not be available in some software applications. JobType. jpg ES 3037/3037e Operation · 115 1. Enter a job name of up to 16 characters under Job Name Setting and a four digit personal ID number. The document will be stored on the printer's hard disk and one copy will print for your perusal. After checking the proof, you then will print or delete (if incorrect) the remaining copies of the document using the procedures given below. Press the MENU button to access the PRINT JOBS MENU, then press the SELECT button. Enter your personal ID number using the buttons on the printer control panel. Press the VALUE button until ALL JOBS or the required job name is displayed. Press the SELECT button to print the remaining copies of the document. Deleting copies from Proof and Print If the proof is not ready for printing, the job must be deleted from the printer: 1. Press the MENU button to access the PRINT JOBS MENU and press the SELECT button. Then open the drop-down menu directly underneath the printer and select Layout. Layout. jpg ES 3037/3037e Operation · 120 3. Click Print to print or Save Settings to save and close the printer dialog box. LayoutOptions. jpg ES 3037/3037e Operation · 121 Duplex 1. Then open the drop-down menu directly underneath the printer and select Layout. 3. From the Layout screen, select the options desired. Layout. jpg a b a. For Duplexing (printing on both sides of the sheet), press the button for Print on Both Sides. ES 3037/3037e Operation · 122 LayoutOptions. jpg b. Normally, the first option is the default. NOTE Duplex printing can only be carried out on standard paper sizes and paper weights between 20 and 28 lb. The optional duplex unit must be installed in the printer and enabled before duplex printing can be carried out. Paper must be loaded into the paper tray with the print side facing upwards. Click Print to print or Save Settings to save and close the printer dialog box. ES 3037/3037e Operation · 123 Collating Collating can be carried out with or without a hard disk drive installed. If the software application being used has a collate print option, it is recommended to use only one collate option to prevent any conflicts in printing, i. e. collate from the software application or collate from the printer driver. [. . . ] Fold the tray media size identifier sheets supplied with the High Capacity Feeder to expose the appropriate media size, then insert them in the holder at the right end of each tray. zmsetup loading paper two. eps and zmsetup loading paper four. eps c9_116. jpg ES 3037/3037e Accessories · 235 5. Place the appropriate self-adhesive tray number identifier labels supplied with the High Capacity Feeder on the lower rectangle at the right side of each tray. 6. Connect the printer interface cable and power cable, then switch on the printer. Print a MenuMap (see "Printing the MenuMap" on page 38) and check that the newly added trays (Tray2, 3 and 4 if only the HCF is installed, or Tray3, 4, and 5 if the optional tray is also installed) appear under the MEDIA MENU. c9_066. jpg ES 3037/3037e Accessories · 236 NOTE To engage the printer's Automatic Tray Switching feature: · Press the MENU button until the PRINT MENU is displayed and press the SELECT button. · Press the VALUE button to change the setting to ON, then press SELECT. [. . . ]