User manual BARTSCHER A190192-134

[. . . ] Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below. DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately and disposed of in a safe manner. [. . . ] • After removing the protective material, immediately insert the drum cartridge in the machine. Do not allow the drum cartridge to be directly exposed to sunlight or electric light. • Do not tilt the drum cartridge or insert it in the wrong direction or orientation. Make sure that the colours on the new drum cartridge and the insertion label match. Replace the developer cartridge and toner collection container, close the front cover of the machine, and turn on the power. 4 For the procedure for replacing the developer cartridge and toner collection container, see steps 6 to 8 and steps 10 to 11 of "Replacing the developer cartridge" (page 23). When replacement is finished, colour balance adjustments begin automatically. ☞ Colour balance adjustments (page 31) 34 dxc381_uk_saf. book 35 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Replacing the transfer unit When a message appears prompting you to replace the transfer unit, replace the transfer unit. The transfer unit consists of the primary transfer belt unit inside the machine and the secondary transfer roller unit under the right cover. Replacing the primary transfer belt unit When it is time to replace a supply item, a message instructing you to replace the item will appear in the display. • Do not replace a supply item before the replacement message appears in the display. • Install the new primary transfer belt promptly after the primary transfer belt unit has been removed. Light entering through openings in the machine may damage the drum cartridges. Press the [POWER] key ( ) on the operation panel to turn off the panel power, and then switch the main power switch to the off position. 1 Caution After the main power is turned off, the primary transfer belt unit will be hot. Wait about 5 minutes for the machine to cool. 35 dxc381_uk_saf. book 36 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Open the front cover and remove the toner collection container. ☞ Replacing the toner collection container (page 19) 2 Do not point the holes down as used toner will spill out. Securely close the bypass tray and then open the right cover. 3 Turn the lock levers in the direction of an arrow below and release the primary transfer belt unit. 4 36 dxc381_uk_saf. book 37 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Slowly pull out the primary transfer belt unit. (1) Grasp the primary transfer unit as shown below and slowly pull it out. Transfer belt Fall prevention lock Handle 5 (2) Hold down the fall prevention lock with one hand, grasp the handle with your other hand, and remove the primary transfer belt unit. Grip the frame of the primary transfer belt unit with your left hand and hold down the fall prevention lock on the left side with your left thumb. Pull the band-shaped green handle on the right side up and grasp it with your right hand. Caution Always hold the primary transfer belt unit with both hands. A new ozone filter is included in the fusing unit box. Slide the cover on the right side of the machine toward the inside to remove it. 1 Remove the ozone filter. 2 Install a new ozone filter. 3 50 dxc381_uk_saf. book 51 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Attach the cover. 4 51 dxc381_uk_saf. book 52 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Replacing the staple cartridge in the finisher When the staple cartridge runs out of staples, a message will appear in the operation panel. Follow the procedure below to replace the staple cartridge. Open the cover. 1 While pressing the lever over to the left, slide the finisher to the left until it stops. Gently slide the finisher until it stops 2 Lower the staple case release lever and remove the staple case. Pull the staple case out to the right. 3 52 dxc381_uk_saf. book 53 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Remove the empty staple cartridge from the staple case. Gently grasp the right side of the staple cartridge as shown and lift to the left and up. After the lock releases, continue lifting the staple cartridge to the left and up to remove it. 4 • Even when a message appears in the operation panel, staples may occasionally remain in the staple cartridge. Forcing the lock to release may deform the staple case and staple cartridge, causing failure. Insert a new staple cartridge into the staple case as shown. Push the staple cartridge in until it clicks into place. 5 53 dxc381_uk_saf. book 54 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Replace the staple case. Push the staple case in until it clicks into place. 6 Slide the finisher back to the right. Gently slide the finisher back to the right until it locks into its original position. 7 Take care that your fingers are not pinched when closing the cover. Close the cover. 8 Take care that your fingers are not pinched when closing the cover. Make a test print or copy in staple sort mode to verify that stapling takes place correctly. 54 dxc381_uk_saf. book 55 ページ ２００８年１１月１２日　水曜日　午前９時２３分 REPLACING SUPPLIES AND MAINTENANCE Regular maintenance To ensure that the machine continues to provide top quality performance, periodically clean the machine. Caution Do not use a flammable spray to clean the machine. If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine, fire or electrical shock may result. • Do not use thinner, benzene, or similar volatile cleaning agents to clean the machine. • When using the DX-C311/DX-C381, use a soft cloth to gently wipe off dirt from the area on the operation panel with a mirror-like finish (shown at right). The area with a mirror-like finish is the area that is . Cleaning the document glass and automatic document feeder If the document glass or document backplate sheet becomes dirty, the dirt will appear as dirty spots, coloured lines, or white lines in the scanned image. If necessary, moisten the cloth with water or a small amount of neutral detergent. After wiping with the moistened cloth, wipe the parts dry with a clean dry cloth. Document glass Document backplate sheet Scanning area • When wiping dirt off the machine, do not press down hard on the machine. [. . . ] • PostScript is a registered trademark of Adobe Systems Incorporated. • Adobe and Flash are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries. • Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries. • Macintosh, Mac OS, AppleTalk, EtherTalk and LaserWriter are trademarks of Apple Inc. , registered in the U. S. [. . . ]