User manual BARTSCHER A153.080 DATASHEET

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Oki Printing Solutions are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh, Mac, and Mac OS are registered trademarks of Apple Computers Inc. Hewlett-Packard, HP, and LaserJet are registered trademarks of Hewlett-Packard Company. [. . . ] 7. 8. Refer to the section entitled "Getting started" on page 41 and "Appendix B ­ Menu system" on page 107 for examples of using the menus. C9650 User's Guide> 40 GETTING STARTED This section provides information to help you get started with using your printer. PRINTER LOCATION Check that you have sufficient space for access: > around your printer: 20cm 8in 60cm 24in 60cm 24in 100cm 40in C9650 User's Guide> 41 > above your printer: 70cm 28in TURNING OFF/ON TURNING OFF No hard disk drive installed 1. If a hard disk drive is NOT installed, use the On/Off switch. C9650 User's Guide> 42 Hard disk drive installed 1. If your printer has a hard disk drive installed, hold down the Shutdown/Restart button (1) on the control panel for more than 2 seconds to start the shutdown process. 1 2. When the display panel shows that you can either turn off or restart the printer, use the On/Off switch to turn off the printer. C9650 User's Guide> 43 TURNING ON NOTE If the display panel shows that you can either turn off or restart the printer, press Shutdown/Restart to turn on the printer. 1. If the printer is turned off (no power), use the On/Off switch to turn on the printer. CHANGING THE DISPLAY LANGUAGE The default language used by your printer for display messages and for report printing is English. If required, this can be changed using the Panel Language Download Utility located on the installation CD under Optional Utilities. C9650 User's Guide> 44 CHECKING CURRENT SETTINGS Carry out the following steps to generate a Configuration report (Menu Map) to confirm that your printer is correctly configured. Ensure that there is Letter paper in Tray 1 (to be used in this operation). Ensure that the display panel indicates that the printer is ready to print. Press the Up-arrow or Down-arrow buttons repeatedly until Print Information is highlighted. Press the Up-arrow or Down-arrow buttons repeatedly until Configuration is highlighted. Press the Enter button to execute the command and a Configuration document is printed. After printing the configuration document, the printer returns to the ready to print status. System values and installed accessories are listed at the top of the first page while status values and settings follow. C9650 User's Guide> 45 INTERFACES AND CONNECTION Your printer is equipped with a selection of data interfaces: > Parallel ­ For direct connection to a PC. Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). 1 2 3. Close the top cover. C9650 User's Guide> 54 CLEANING THE PAPER FEED ROLLERS Clean the paper feed rollers if paper jams frequently occur. Remove items like a wrist watch or bracelet and follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Open Tray 1 side cover and pull out the paper guide plate (1). 1 C9650 User's Guide> 55 3. Remove Tray 1 completely from the printer. 4. Gaining access through the gap left by Tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly moistened with water. 2 5. Replace Tray 1. C9650 User's Guide> 56 6. Return the paper guide plate to its original position and close Tray 1 side cover. 7. Turn on the printer. C9650 User's Guide> 57 CLEANING THE PRINTER CASING 1. Follow the correct steps to turn the printer off depending on whether a hard disk drive is installed. 2. Wipe the printer surface with a soft cloth moistened sparingly with water or neutral detergent. 3. Use a soft dry cloth to dry the printer surface. C9650 User's Guide> 58 4. Turn on the printer. EMPTYING THE PUNCH CHIP BOX (PUNCH UNIT OPTIONAL ACCESSORY) When the display panel indicates that the punch chip box is full, empty the box as follows: 1. Operate the Finisher lever and move the Finisher away from the printer. C9650 User's Guide> 59 2. Pull out the punch chip box, being careful to keep it level so as not to spill any chips. 3. Discard the chips in an appropriate place. 4. Replace the punch chip box carefully into the Finisher. C9650 User's Guide> 60 5. Check that the punch chip box has been replaced correctly then move the Finisher back into position, being careful not to trap your fingers. C9650 User's Guide> 61 OPTIONAL ACCESSORIES This section describes optional accessory equipment for your printer. The following accessories are available: > duplex unit (to enable two-sided printing) (C9650n only) > additional RAM memory > hard disk drive (required for verified and spooled printing, direct printing of PDFs, when collation errors appear, adding extra fonts) (C9650n and C9650dn only) > second, third paper tray (to increase paper input capacity) > high capacity feeder (equivalent to three paper trays) NOTE Tray configurations are: Tray 1 only, Tray 1 + 2nd Tray, Tray 1 + 2nd Tray + 3rd Tray, Tray 1 + HCF, Tray1 + 2nd Tray + HCF. > Finisher (for stapling printer output) > Punch unit (to extend Finisher functionality) C9650 User's Guide> 62 ACCESSORY ORDER INFORMATION ITEM Duplex unit Additional RAM memory 256 MB 512 MB Hard disk drive Second, third paper tray High capacity feeder (HCF) Finisher: 4-tray 5-tray Finisher Punch Unit: 2-3 hole 42872902 42940201 42872701 70050301 70050401 70050501 42831301 42831501 ORDER NUMBER 42797201 C9650 User's Guide> 63 INSTALLING ACCESSORIES Each accessory (apart from the Finisher) comes complete with its own documentation which gives full instructions on installation. After installation, print out a Menu Map (Configuration document) to check that the installation has been successful. NOTE The Finisher and Punch unit must be installed by an authorized engineer. For the following accessories, you have to make the appropriate setting in your printer driver(s): > duplex unit > paper tray(s) > Finisher Refer to the Printing Guide for driver setting details. C9650 User's Guide> 64 TROUBLESHOOTING GENERAL If the printer display panel does not display anything or is still in stand-by mode 10 minutes after switching on, follow the printer shutdown sequence to switch it off. If the problem persists, contact your dealer. PAPER JAMS This section provides information to help you deal with problems that may arise when using the printer. The following paragraphs describe actions to take in the event of a paper jam and how to deal with unsatisfactory print results. Display panel messages about paper jams and relevant actions are given in this section while a list of other typical messages and suggested responses is given in "Appendix A ­ Display Panel Messages" on page 105. PAPER JAMS ­ PRINTER If a paper jam occurs, a message appears on the display panel in the printer Control Panel. [. . . ] Decrement setting when a white horizontal dotted line or a snowing image occurs in highcoverage print portions. Increment setting when a faded image occurs. Duplex Y Adjust 0. 00 +0. 25 ­ +2. 00 -2. 00 ­ -0. 25 mm 0. 00 +0. 01 ­ +0. 08 -0. 08 ­ -0. 01 in Paper Black Setting 0 +1 +2 -2 -1 C9650 User's Guide> 122 ITEM Paper Color Setting VALUE 0 +1 +2 -2 -1 DESCRIPTION Used for fine color adjustment for a significantly white horizontal dotted line, a significantly faded image or other such a problem that occurs in results printed on plain paper. Decrement setting when a white horizontal dotted line or a snowy image occurs in highcoverage print portions. Used for fine black adjustment for a significantly white horizontal dotted line, a significantly faded image or other such a problem that occurs in results printed on transparencies. [. . . ]