User manual BARTSCHER A153.065 DATASHEET

[. . . ] This table provides specifications to properly load a variety of different specialty media. 2. Install the Custom Printer Drivers The drivers are located on the driver CD supplied with your BARTSCHER C9600 Signage printer. See the Software Installation Guide for complete installation instructions. 4 ADDITIONAL SIGNAGE SOFTWARE SOLUTIONS To further enhance your color signage productivity, these free software programs are available on our web site, www. okidata. com: · Distributed Printing for BARTSCHER · PrintSuperVision. net See page 11 for more information about these programs. PURCHASING BARTSCHER PRINTING SOLUTIONS SPECIALTY MEDIA BARTSCHER Media can only be purchased directly through your reseller. See the complete BARTSCHER Retail Signage Media Collection on page 17. 5 Media Settings This table shows the printer driver settings to use for each type of media. [. . . ] (Ultra Heavy 3) Make sure to open the printer's face-up stacker door. 10 PT Glossy Paper MP Tray 30 sheets max Long Edge Face-up Ultra Heavy 2 or Tray 1 Max fill to black line on label (See illustration on right. ) Long Edge Face-up Ultra Heavy 2 Make sure to open the printer's face-up stacker door when "Stacker face-up" is selected. (See illustration above. ) 6 Media Input Tray Capacity Input Orientation Short Edge Output Bin/ Orientation Face-up Media Type Setting Table Tents (Ultra Heavy 2) Special Conditions/Cautions Fold-up Table Tents (3 up per sheet) 12" x 19. 125" MP Tray 30 sheets max · Be sure to open the face-up stacker. (See illustration above. ) · Separate each sheet carefully to avoid multi-sheet feeding. · Check for paper dust and chaff, particularly around the cut edge of the media. Completely fan cling film sheets to separate before inserting in the paper tray. 12 x 12 Corner Clings - Triangle die-cut adhesive 4-Up White Low Tack Laser Labels 8. 5" x 14" MP Tray 30 sheets max 30 sheets max __ Face-up Corner Cling (Ultra Heavy 2) White Labels (Ultra Heavy 1) MP Tray Short Edge Face-down or Tray 1 Max fill to blue line on label (See illustration on right. ) 30 Sheets max Short Edge Face-down White Labels (Ultra Heavy 1) 4-Up Frosted Low Tack Laser Vinyl 8. 5" x 14" or as appropriate MP Tray Short Edge Face-down Frosted Labels (Ultra Heavy 1) or Tray 1 Max fill to blue line on label (See illustration on right. ) 30 Sheets Short Edge Face-down Frosted Labels (Ultra Heavy 1) Shelf Strip Media strips (Matte) 8. 5" x 11" or as appropriate MP Tray Short Edge Face-up Shelf Strips Matte (User Type 1) · Long edge feeding should not be used, as multiple sheet feeds will occur. · Make sure to open the printer's face-up stacker door. or Tray 1 Max fill to red line on label (see illustration on right. ) Short Edge Face-up Shelf Strips Matte (User Type 1) 7 Media Input Tray Capacity Input Orientation Short Edge Output Bin/ Orientation Face-up Media Type Setting Shelf Strips Gloss (User Type 2) Special Conditions/Cautions Shelf Strip Media Gloss six 8. 5" x 11" strips MP Tray 30 Sheets · Separate each sheet carefully to avoid multi-feeds. · Make sure to open the printer's face-up stacker door. 4-up Perf 8. 5" x 11" Matt Wobbler 4-up Perf 8. 5" x 11" Gloss Wobbler MP Tray 30 Sheets Short Edge Short Edge Face-up Wobbler Matt (User Type 1) Wobbler Gloss (User Type 2) Make sure to open the printer's face-up stacker door. (See illustration above. ) · Make sure to open the printer's face-up stacker door. (See illustration above. ) · Separate each sheet carefully to avoid multi-sheet feeding. (See illustration above. ) · Separate each sheet carefully to avoid multi-sheet feeding. · Excess glue from the edges of this media could damage/ shorten the printer and consumables life. Dampen a soft, lint-free cloth with 90% isopropyl alcohol, then use the cloth to clean the outer roller. 3. Lift the MP Tray slightly and pull in on the hinge to release the pin from the track. Use a fresh area of the cleaning cloth to wipe the rubber pad on the front roller access door. 9. Lower the top roller cover, then lift the MP Tray slightly and place the hinge pins on each side back in the track. 7. Dampen a soft, lint-free cloth with 90% isopropyl alcohol, then use the cloth to wipe all three rollers clean. 11. Move the paper guides back to fit the print media, then replace the media in the MP Tray. 14 Troubleshooting PAPER JAMS AT THE MULTI-PURPOSE TRAY Phenomenon Printer LCD displays CHECK MPTRAY / 390: PAPER JAM Potential Cause #1 Improper paper tray was used or recommended Tray Capacity was not followed. Suggested Action Use specified paper tray for media as recommended in "Media Settings" table on page 6. Reinstall and use the PostScript driver. Potential Cause #3 Media Check setting is not cleared in the printer driver. Suggested Action See "Setting Up the Printer Driver for Signage" on page 9. PRINTED IMAGE WAS ROTATED 90 DEGREES Phenomenon The printed results appear 90 degrees rotated. Potential Cause Wrong paper size orientation was set in the printer menu. All paper trays, except the Multi-purpose tray, have a paper size sensor. [. . . ] index · 8. 5" x 11" · 250 sheets per box · Uniformly smooth surface enhances ink holdout and overall printability · Color visuals are vibrant against all backgrounds · Improved clarity for extra impact SHELF STRIPS Part No. 52207401 · 6 @ 1. 25" x 11" (8. 5" x 11") · 100 sheets per box · Water resistant and scratch-proof · Printable on both sides · Easy to apply CLEAR FILM CLING LABELS Part No. 52207802 · 8. 5" x 11" · 100 sheets per box · Easy to apply and remove · Can be applied to smooth surfaces including beverage coolers, windows and vehicles PREMIUM 10 PT. 52207603 · 11" x 17" · 1, 000 sheets per box · Bright gloss-finish sheets · Enhance printed color visuals BANNER PAPER Part No. [. . . ]