User manual BARTSCHER A153.060 DATASHEET

[. . . ] Load Your Media Use the "Media Setting" table on page 6 to set up your media in the printer driver. This table provides specifications to properly load a variety of different specialty media. 2. Install the Custom Printer Drivers The drivers are located on the driver CD supplied with your BARTSCHER C9600 Signage printer. See the Software Installation Guide for complete installation instructions. 4 ADDITIONAL SIGNAGE SOFTWARE SOLUTIONS To further enhance your color signage productivity, these free software programs are available on our web site, www. okidata. com: · Distributed Printing for BARTSCHER · PrintSuperVision. net See page 12 for more information about these programs. PURCHASING BARTSCHER PRINTING SOLUTIONS SPECIALTY MEDIA BARTSCHER Media can only be purchased directly through your reseller. [. . . ] (See illustration above. ) · Separate each sheet carefully to avoid multi-sheet feeding. · Check for paper dust and chaff, particularly around the cut edge of the media. Completely fan cling film sheets to separate before inserting in the paper tray. 12" x 12" Corner Clings - Triangle die-cut adhesive 4-Up White Low Tack Laser Labels 8. 5" x 14" MP Tray 30 sheets max 30 sheets max __ Face-up Corner Cling (Ultra Heavy 2) White Labels (Ultra Heavy 1) MP Tray Short Edge Face-down or Tray 1 Max fill to blue line on label (See illustration on right. ) 30 Sheets max Short Edge Face-down White Labels (Ultra Heavy 1) 4-Up Frosted Low Tack Laser Vinyl 8. 5" x 14" or as appropriate MP Tray Short Edge Face-down Frosted Labels (Ultra Heavy 1) or Tray 1 Max fill to blue line on label (See illustration on right. ) 30 Sheets Short Edge Face-down Frosted Labels (Ultra Heavy 1) Shelf Strip Media strips (Matte) 8. 5" x 11" or as appropriate MP Tray Short Edge Face-up Shelf Strips Matte (User Type 1) · Long edge feeding should not be used, as multiple sheet feeds will occur. · Make sure to open the printer's face-up stacker door. or Tray 1 Max fill to red line on label (see illustration on right. ) Short Edge Face-up Shelf Strips Matte (User Type 1) 7 Media Input Tray Capacity Input Orientation Short Edge Output Bin/ Orientation Face-up Media Type Setting Special Conditions/Cautions Shelf Strip Media Gloss six 8. 5" x 11" strips MP Tray 30 Sheets Shelf Strips Gloss (User Type 2) · Separate each sheet carefully to avoid multi-feeds. · Make sure to open the printer's face-up stacker door. 4-up Perf 8. 5" x 11" Matte Wobbler 4-up Perf 8. 5" x 11" Gloss Wobbler MP Tray 30 Sheets Short Edge Short Edge Face-up Wobbler Matte (User Type 1) Wobbler Gloss (User Type 2) Make sure to open the printer's face-up stacker door. (See illustration above. ) · Make sure to open the printer's face-up stacker door. (See illustration above. ) · Separate each sheet carefully to avoid multi-sheet feeding. (See illustration above. ) · Separate each sheet carefully to avoid multi-sheet feeding. · Excess glue from the edges of this media could damage/ shorten the printer and consumables life. (See illustration above. ) · Monitor exiting cling sheets until job is complete. · Excess glue from the edges of this media could damage/ shorten the printer and consumables life. MP Tray 30 Sheets Face-up Clear Cling Film 8. 5" x 11" MP Tray 30 Sheets Long Edge, Non-perf edge in first Face-up Clear Cling (User Type 3) White Cling Film 8. 5" x 11" MP Tray 30 Sheets Long Edge, Non-perf edge in first Face-up White Cling (User Type 4) 8 Media Input Tray Capacity Input Orientation Short edge Output Bin/ Orientation Face-up Media Type Setting Special Conditions/Cautions Banner Paper 12. 9" x 35. 4" MP Tray 30 Sheets max Heavy · Make sure to open the printer's face-up stacker door. · If the banner does not print, change the Quality selection to Fine on the Job Options tab. Dampen a soft, lint-free cloth with 90% isopropyl alcohol, then use the cloth to clean the outer roller. 3. Lift the MP Tray slightly and pull in on the hinge to release the pin from the track. Use a fresh area of the cleaning cloth to wipe the rubber pad on the front roller access door. 9. Lower the top roller cover, then lift the MP Tray slightly and place the hinge pins on each side back in the track. 7. Dampen a soft, lint-free cloth with 90% isopropyl alcohol, then use the cloth to wipe all three rollers clean. 11. Press the VALUE+ button repeatedly until the paper size that you wish to use displays. Suggested Action 1. Press the VALUE+ button repeatedly until the paper size that you wish to use displays. Potential Cause #2 You are using the PCL driver. Suggested Action Only the PostScript driver can print on custom media properly. Reinstall and use the PostScript driver. BANNER DID NOT PRINT Phenomemon Banner does not print. Potential Cause Banner image is too complex for the printer's memory. Suggested action On the Job Options tab in the printer driver, change the Quality Setting from Photo (default) to Fine. Potential Cause #3 Media Check setting is not cleared in the printer driver. [. . . ] index · 8. 5" x 11" · 250 sheets per box · Uniformly smooth surface enhances ink holdout and overall printability · Color visuals are vibrant against all backgrounds · Improved clarity for extra impact SHELF STRIPS Part No. 52207401 · 6 @ 1. 25" x 11" (8. 5" x 11") · 100 sheets per box · Water resistant and scratch-proof · Printable on both sides · Easy to apply CLEAR FILM CLING LABELS Part No. 52207802 · 8. 5" x 11" · 100 sheets per box · Easy to apply and remove · Can be applied to smooth surfaces including beverage coolers, windows and vehicles PREMIUM 10 PT. 52207603 · 11" x 17" · 1, 000 sheets per box · Bright gloss-finish sheets · Enhance printed color visuals BANNER PAPER Part No. [. . . ]