User manual BARTSCHER 288401 CONTROL PLAN

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://my. okidata. com Trademark Information _______________________________ Oki and Microline are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks of Apple Computers Inc. Hewlett-Packard, HP, and LaserJet are registered trademarks of Hewlett-Packard Company. [. . . ] Set the IP Address in the printer: B4400/4500/4550/4600 User's Guide 61 NOTE: Proceed to Install the Printer Driver if the IP address has been set in Windows or obtained automatically. Press Value+ or Value- to display the first digit value of the IP address. Repeat steps 3 to 5 to set IP 2/4 to IP 4/4, MASK 1/4 to Mask 4/4, (Subnet mask), Gate 1/4 to Gate 4/4, (Gateway address). On the hard disk select Applications>Utilities folder, and double-click Printer Setting Utility. 7. B4400/4500/4550/4600 User's Guide 62 Bonjour (Rendezvous) Protocol 1. On the hard disk select Applications>Utilities folder, and double-click Printer Setting Utility. Select the printer name in Printer Types, and select a printer name to be used for Mac OS X 10. 3 or earlier. 9. A printer name is "BARTSCHER B4500n" plus the last 6 digits of the MAC address. 10. Close the Printer Setting Utility. B4400/4500/4550/4600 User's Guide 63 Setup for Mac OS X via USB Connection Requirements: A Macintosh computer Rev 8. 1 to 9. 2. 2 and Mac OSX. Connecting a Cable A printer cable is not supplied with the printer. Turn off the Macintosh and the printer. S M Printer State tab. jpg 1 2. 3. Insert a USB cable into the USB interface connector (1) of the printer. Always use this tray and the manual feed tray for heavyweight stocks to reduce the possibility of paper jams. Automatic feed sequence Ensure that the Autotray function is set to ON (default) when you have either or both optional feed trays installed. In this way, if a tray runs out of paper, automatic feed will take place in the order Tray 1, Tray 2 (if installed), provided that these trays are set up for identical media. B4400/4500/4550/4600 User's Guide 68 Printing envelopes 1. Pull out the rear paper exit tray (1) until it locks and lift out the paper guide (2). 2 1 Fig1_05. jpg 3 2. 4. Pull down the manual feed tray (3) and adjust the paper guides to the width of the envelope. Insert the envelope, flap down and to the left, until the printer grips it. Set envelope size and landscape orientation in your software, then issue the print command. Heavyweight paper or cardstock The normal paper path from a main paper tray to the top output stack involves two complete U-turns. This may sometimes cause very heavyweight paper or cardstock to jam or misfeed. Use the manual feed (multi-purpose) tray to feed this type of paper and the rear paper exit to collect printed output. This gives a nearly straight paper path through the machine and may prove more reliable in this type of application. Paper feed, size and media setting The process used to fuse (fix) the printed image to the paper involves a mixture of pressure and heat. Too much heat will cause lightweight paper to crease or curl, and corrugations in transparencies. Too little heat will cause the image not to fuse fully into heavyweight paper. [. . . ] Recommended operating humidity: 20-80% High humidity. Software problems Your software (operating environment, applications and printer drivers) controls the printing process. Make sure you B4400/4500/4550/4600 User's Guide 97 have selected the right driver for use with your printer. See your software documentation for more information. Symptom Printing is garbled. Problem Incorrect driver is installed. Solution Install an appropriate driver. Printer's output is Much of the printing For maximum speed, use text in below rated delays will be your document and use a printer speed. Sometimes purely text documents will print slowly depending on the selected fonts and how they are transferred to the printer. [. . . ]