User manual BANG & OLUFSEN BEOLINK 5000

[. . . ] cloth may be cleaned with a To restore the sound: vacuum cleaner with a soft brush > Disconnect the loudspeaker from nozzle, and set to the lowest level. > Allow the system time to reset or Never use alcohol or other solvents to clean any parts of the loud cool down (approximately 3­5 speaker! > Reconnect the loudspeaker to To switch on and off the mains supply. When you switch on your Bang & Should the problem persist, Olufsen system, the loudspeaker contact your Bang & Olufsen switches on simultaneously, and retailer. [. . . ] when you switch the system off again, the loudspeaker also switches to standby. When you have finished setting up the loudspeaker as described on the following pages, connect the entire system to the mains. 4 Set up the loudspeaker ­ cable connections The loudspeaker socket panel is located on the rear. Insert the cables and set the POSITION switch before you fasten the loudspeaker to the wall bracket. For information about the sockets on the Bang & Olufsen system, refer to the Guides enclosed with the product. Before you make any connections, disconnect your Bang & Olufsen system from the mains supply! POWER LINK socket Cable clamp POSITION switch Power Link Mk 3 POWER LINK socket: Use this socket to connect the loudspeaker to one of the Power Link sockets on the Bang & Olufsen system. Note: Do not use a Power Link cable of the older type, as this will cause noise, and therefore not give optimum sound quality!The new type has a triangular mark on the plug. Cable clamp: For safety reasons, the mains cord from the wall outlet must be secured to the loud speaker. Mains cord: The supplied mains cord and plug are specially designed for the product. If you change the plug or damage the mains cord, you must buy another from your Bang & Olufsen retailer! 5 The POSITION switch When a loudspeaker is placed in a corner or close to a wall, the bass level is boosted compared to the bass level from a loudspeaker placed in a more free-standing position. To remove this excessive bass boost, use the POSITION switch to ensure that the bass level suits the placement of the loudspeaker. The correct position is obtained when the front of the loud¬speaker cabinet falls 13 mm (0. 51") `behind' the front of the television screen. ­ Tighten the screws at the end of all three struts ­ in order to lock the loudspeaker position onto the wall bracket. 13 mm 0. 51" 13 mm 0. 51" Loudspeaker position: The wall bracket allows you to adjust the loud speaker fronttoback position for use with different television screen sizes. For safety reasons, it is important that you lock the loudspeaker onto the wall bracket! To attach the loudspeaker front panel 1 Insert all the little pegs on the rear side of the panel into the corresponding holes in the loud speaker cabinet. When finished, the loudspeaker front panel must be aligned with the front of the television screen. If it apppears not to be so, remove the loudspeaker front panel again, and adjust the fronttoback position of the loudspeaker. To remove the front panel, for example for cleaning, just pry the little pegs free from the loud speaker cabinet. Cover plates: If your loud¬speaker is set up beneath a 65inch screen, fasten two cover plates to the wall bracket ­ one on each side of the bracket. ×2 10 Waste Electrical and Electronic Equipment (WEEE) ­ Environmental protection Electrical and electronic equipment, electronic equipment, batteries parts and batteries marked with and waste prevents the potential this symbol must not be disposed contamination of nature with the of with normal household hazardous substances which may wastage; all electrical and be present in electrical and electronic equipment, parts and electronic products and equipment batteries must be collected and Your Bang & Olufsen retailer will disposed of separately. advise you of the correct way of When disposing of electrical and disposal in your country. [. . . ] ×2 10 Waste Electrical and Electronic Equipment (WEEE) ­ Environmental protection Electrical and electronic equipment, electronic equipment, batteries parts and batteries marked with and waste prevents the potential this symbol must not be disposed contamination of nature with the of with normal household hazardous substances which may wastage; all electrical and be present in electrical and electronic equipment, parts and electronic products and equipment batteries must be collected and Your Bang & Olufsen retailer will disposed of separately. advise you of the correct way of When disposing of electrical and disposal in your country. electronic equipment and batteries If a product is too small to be by use of the collection systems marked with the symbol, it will available in your country, you appear in the User Guide, on the protect the environment, human Guarantee certificate, or on the health and contribute to the prudent and rational use of natural packaging. This class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. [. . . ]