User manual BALAY 3VS851ID

[. . . ] EN Instructions for use Dishwasher . en Index 4 6 7 8 9 10 11 15 auto 3in1 . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. The wooden frames (if fitted) are made of residual wood and are untreated. The hoops (if fitted) consist of polypropylene (PP). Installation Install and connect the appliance according to the installation and assembly instructions. [. . . ] 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 9 on or off. Hold down the programme button 4 and press the main switch 1 until the digital display lights up, then release the buttons. 3 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button 4 , you can switch off or switch on the rinse aid indicator. Switch off the main switch 1 ; the setting is saved. 17 en Programme overview This overview lists the max. The programmes supplied with your appliance are indicated on the fascia. Type of crockery e. g. china, pots/pans, Nondelicate cutlery, glasses, etc. Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard medium Mixed Delicate Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads very little Amount of food remains Condition of food remains Wash programme a little Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. loosely attached Intesive 70° Auto 55° /65° Eco 50° Gentle 40° Quick 45° Pre-rinse The programme sequence is optimized and adapted with how the appliance is loaded and how dirty the dishes are. Programme sequence Pre-rinse 50° Wash 70° First rinse Second rinse Third rinse Rinse-aid 70° Drying Pre-rinse Wash 50° Main rinse Rinse-aid 65° Drying Pre-rinse Wash 40° Main rinse Rinse-aid 55° Drying Wash 45° Main rinse Rinse-aid 55° Pre-rinse Drying Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching the dishwasher ON Turn on the tap. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed. The programme starts automatically. Programme specifications The programme specifications can be found in the summary of instructions. Greater deviations may occur due to: varying amounts of dishes water supply temperature water pipe pressure ambient temperature mains voltage tolerances and the tolerances specific to the appliance (e. g. temperature, amount of water, etc. ) The water consumption values refer to a set water hardness value of 4. 7 Programme sequence indicator Your dishes are being cleaned. Your dishes are being dried. End of programme The programme has ended when a figure appears in the numerical display 3 . Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. When the Aqua sensor is active, "clean" rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. [. . . ] When replacing the appliance, always connect a new water supply hose to the water supply. Water pressure: Minimum 0, 05 MPa (0, 5 bar) ­ maximum 1 MPa (10 bar). If you do use hot water, the temperature should not exceed 60 °C. Delivery Your dishwasher was checked at the factory to ensure that it was in perfect working order. These will disappear after the first rinse cycle. Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed socket with protective conductor. [. . . ]