User manual BALAY 3VN552BD

[. . . ] LQVWUXFWLRQ PDQXDO 9000 288 470 (9009) (1 'LVKZDVKHU \ ZZZEDOD\HV en Table of contents Washing the dishes . 15 15 15 15 15 16 16 16 16 16 16 17 17 17 17 18 18 19 19 19 20 20 21 22 22 22 23 23 23 23 24 24 24 24 25 25 25 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. § Half load * If you have only a few items to wash (e. g. It is recommended to put a little less detergent in the detergent dispenser than for a full load. ­ Timer programming * You can delay the start of the programme in 1 hour steps up to 19 hours. ­ Press the timer programming button until the digital display ` jumps to . ­ Keep pressing the timer programming button until the required time is displayed. ­ To delete the preselected starting time, press the button until is indicated on the digital display `. You can change your programme selection at any time until the programme starts. Switching on the appliance ­ Turn on the tap fully. The expected programme duration is indicated on the numerical display `. ­ The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display `. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). 15 en End of programme The programme has ended when the value is indicated on the numerical display `. Changing the programme After you have switched the appliance on, it is possible to change the programme within 2 min. If you want to change the programme afterwards, the appliance waits until the initiated programme section (e. The remaining time comprises the remaining time of the previous programme section and the remaining time of the new selected programme. Switching off the appliance Short time after the end of the programme: ­ Switch off the main switch (. ­ Remove the utensils when they have cooled down. Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Hold down button + and press main switch ( until the digital display illuminates. To change the setting: ­ By pressing the button +, you can switch intensive drying on or off . The set value is saved. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Switch off the main switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ To continue the programme, switch on the main switch ( again. Terminating the programme (Reset) ­ Only when the main switch is on: Rotate programme selector 8 to the Reset position. ­ Switch off the main switch (. 16 en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Filters The filters 1J keep large foreign objects in the rinsing water away from the pump. ­ After each wash cycle check the filters for residue and clean if required. [. . . ] temperature 60 °C. Waste-water connection ­ The required work sequence can be found in the installation instructions. ­ Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts. Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out! Fresh water connection ­ Connect the fresh-water connection to the tap according to the installation instructions with the enclosed parts. Ensure that the fresh-water connection is not kinked, crushed or twisted. [. . . ]