User manual BALAY 3VI951XD

[. . . ] Instructions for use en 9000 040 667 (8406) en en Index 4 6 6 7 8 9 10 13 15 Programme overview . . 3 en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Please dispose of packaging material properly: D The corrugated cardboard consists mainly of waste paper. D The polyethylene film (PE) consists partly of secondary raw material. [. . . ] As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. Switching the rinse aid refill indicator off and on Hold down the programme button 3 and press the main switch 1 until the digital display lights up, then release the buttons. Each time the button 3 is pressed, the set value increases by one; when the value is reached, the display jumps back to . Switch off the main switch 1 ; the setting is saved. 16 en Programme overview This overview lists the max. The programmes supplied with your appliance are indicated on the fascia. Type of crockery e. g. china, pots/pans, Nondelicate cutlery, glasses, etc. Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard medium Mixed Delicate Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads very little Amount of food remains Condition of food remains Wash programme a little Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. loosely attached Intesive 70° Auto 55° /65° Eco 50° Gentle 40° Quick 45° Pre-rinse The programme sequence is optimized and adapted with how the appliance is loaded and how dirty the dishes are. Programme sequence Pre-rinse 50° Wash 70° First rinse Second rinse Third rinse Rinse-aid 70° Drying Pre-rinse Wash 50° Main rinse Rinse-aid 65° Drying Pre-rinse Wash 40° Main rinse Rinse-aid 55° Drying Wash 45° Main rinse Rinse-aid 55° Pre-rinse Drying Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching the dishwasher ON Turn on the tap. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed The numerical display 8 shows the expected duration of the programme. The programme starts automatically. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e. g. Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. 9 Programme sequence indicator )n )n )n 49 h6 + 6 069ng 3V6+n64( 49 h6 + 6 069ng 9n 64( 49 h6 + 6 069ng 4 964( Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device's door. In the case of built-in dishwashers with flush front the light point will not be visible. Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. When the Aqua sensor is active, "clean" rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. 4 litres for utensils which are "less" dirty. End of programme The end of the programme is indicated by a buzzer. This function can be changed as follows:­ Hold down Function button C pressed and switch on main switch 1 , then let the buttons go. Function Button C flashes, and the digital display indicates the value which was set at the factory (semi-loud). Each depression of the button increases the set value by one, when is reached, the display jumps back to (off). 18 en Switch off the main switch 1 . [. . . ] When replacing the appliance, always connect a new water supply hose to the water supply. Water pressure: Minimum 0, 05 MPa (0, 5 bar) ­ maximum 1 MPa (10 bar). If you do use hot water, the temperature should not exceed 60 °C. Removing the appliance It is essential, when removing the appliance, to observe the following sequence: First, disconnect the appliance from the power supply. Pull out the appliance, carefully pulling the hose behind. Transporting the dishwasher Drain water from the dishwasher. [. . . ]