User manual BALAY 3VH302NA

[. . . ] instruction manual 9000 481 579 (8907-1) EN Dishwasher y www. balay. es 3 ABC 12 11 10 Reset 3 sec. 9 6 3 Program End Reset 3 sec. Start 1 2 3 4 5 678 9 20 21 22 23 24 25 26 27 28 29 30 31 32 en Table of contents Washing the dishes . 15 15 15 15 16 16 16 16 16 17 17 17 17 17 18 18 19 19 20 20 21 21 22 23 23 23 24 24 24 24 25 25 25 25 26 26 26 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] It is recommended to put a little less detergent in the detergent dispenser than for a full load. ¿ Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 15 en Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. ­ Keep pressing the Preselected starting time button 0 until the appropriate display 3h, 6h or 9h is lit. ­ To delete the preselected starting time, keep pressing the Preselected starting time button 0 until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. Switching off the appliance Short time after the end of the programme: ­ Open the door. ­ Remove the utensils when they have cooled down. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Open the door. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ Close the door. End of programme The programme has ended when the End display ` is lit. ­ Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. ­ Keep pressing button > P until the salt refill indicator )* and rinse aid refill indicator )" flash. The refill indicators )* and )" flash and the displays # and + are lit (= Setting 2). To change the setting, ­ Press the button < H until the required setting has been selected. ­ Close the door. Terminating the programme (Reset) ­ Open the door. ­ Close the door. 16 en Changing the programme When the START button h has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. ­ Keep pressing button > P until the salt refill indicator )* and "Check water supply" )2 flash. To change the setting, ­ Press button < H until the display # is lit (Intensive drying on). ­ Close the door. Overall condition of the machine ­ Check spray arm for grease and limescale deposits. [. . . ] Please note the system will not function unless the power supply is connected. Transportation Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: ­ Turn on the tap. (Buzzer sounds. ) ­ Switch the appliance off ( and turn the tap off. (This prevents residual water from running into the machine control and damaging the programme sequence. ) Removing the appliance Also observe the sequence of worksteps here. [. . . ]