User manual BABYSTYLE OYSTER

[. . . ] This does not affect your statutory rights. www. oysterstroller. com BabyStyle UK Limited LE12 7RJ UNITED KINGDOM This instruction manual © Babystyle UK Limited 2009 All rights reserved. OYSTER AJB1700/071209 2 15 FITTING THE STROLLER RAIN COVER Place the rain cover over the stroller; the rain cover needs the stroller hood to be fitted to support the rain cover. Fasten the Velcro strips at the front of the rain cover around the front legs of the stroller (when the seat unit is facing forwards). When the seat unit is facing rearwards, fasten the Velcro strips at the front of the rain cover around the rear legs to secure. [. . . ] To remove the wheel; push in the front wheel quick release button on the front wheel housing and pull the wheel unit from the axle stub. NOTE, the axle stubs can become greasy and may leave marks on other surfaces they come into contact with. To prevent marking clean the axle stubs with a cloth. To keep the front wheels swivelling freely ensure they are regularly lubricated, if steering becomes stiff, remove front wheel units, clean, lubricate and refit. FITTING THE FOOTMUFF The footmuff top cover can be removed by unfastening the zip. The back part of the footmuff can be used as a seat liner without the top part. To attach the footmuff to the seat unit: Release the harness clips from the centre buckle and release the shoulder straps from the waist belts at the buckle connection. Pass the shoulder straps and waist belts through the corresponding openings in the footmuff. Attach the two press-studs at the rear top of the seat backrest to the two press-studs on the top of the footmuff. 4 13 shoulder straps should be clipped into the centre buckle at the end of the crotch strap. The harness can be adjusted to suit your child by sliding the adjusters along the shoulder straps and waist belts. Drings for attaching a separate harness can be found attached to the integral harness at the base of the waist straps. Thread the buckle through the hole in the plastic seat base and then through the opening in seat covers and reposition, passing back through first the seat cover and then through the opening in plastic seat base. The shoulder straps can be adjusted to two positions', thread the buckle through the hole in the plastic seat back and through the opening in the seat cover and reposition passing first through the seat cover and then through the opening in the plastic seat back. Ensure that both shoulder straps are at the same level and that both are secure. WARNING Always use the crotch strap in combination with the waist belt. ALWAYS USE THE SAFETY HARNESS HOOD/SUN CANOPY/INSECT NET The Oyster has a multi function hood that helps to protect your child from the elements. TO REMOVE/ FIT THE HOOD Release the two press-studs at the back of the hood where the hood attaches to the backrest. Fold the hood back; hold the hood by the frame in the centre and pull the hood up in line with the back rest, the hood will slide away from the fittings on the side of the seat back rest. Line up the plastic components on the hood sides (one left, one right) and slide them into the corresponding plastic parts on the sides of the seat back rest. Fasten the Velcro on the hood to the seat back and secure the press-studs FITTING AND REMOVING THE REAR WHEELS Hold the rear wheel and insert the rear wheel axle stub into the hole in the rear axle. To remove the rear wheel push in and hold the rear wheel quick release lever (on the rear axle) and pull the rear wheel from the axle. NOTE, the axle stubs can become greasy and may leave marks on other surfaces they come into contact with. To prevent marking clean the axle stubs with a cloth. OPERATING THE SWIVEL FRONT WHEELS The front wheels can be used in swivel-wheel or fixed-wheel mode. To switch from locked to swivel; press down the swivel wheel lock buttons (left & right), to switch back to locked; press again and the wheels will lock automatically when they return to the travel forwards position. [. . . ] The car seat can not be attached to the chassis until the seat unit or the carrycot has been removed. Insert the car seat adaptors into the Oyster chassis attachment device, the adaptors are marked "R" and "L" for right and left. Hold the car seat by the carry handle and lower the car seat onto the car seat adaptors. The adaptors should slot into the cavity at the base of the car seat handle left and right. [. . . ]