User manual BABY JOGGER CAR SEAT ADAPTER KIT

[. . . ] Car Seat Adapter Kit For Use With: · City-Single Stroller · Q-Single Stroller · Pram Accessory Read these instructions carefully before use and keep them for future reference. Your child's safety may be affected if you do not follow these instructions. Kit Includes This Adapter Kit Includes: 1 ­ U-Shaped Support Bar 1 ­ T-Shaped Support Bar 1 ­ Spring Support Bar 1 ­ Straight Support Bar 2 ­ Adapter Brackets (1 ­ left, 1 ­ right) U-Shaped Support Bar This will be used to install Peg Perego Primo Viaggio SIP, Graco, Evenflo, and Britax Companion car seats. T-Shaped Support Bar This will be used to install only Britax Companion car seats. Spring Support Bar This will be used to install only Peg Perego Primo Viaggio SIP. Adapter Brackets These will be used to install the Pram, Peg Perego Primo Viaggio SIP, Graco, Evenflo, Britax Companion, and Maxi Cosi car seats. Straight Support Bar This will be used to install only Peg Perego Primo Viaggio SIP. Pram (Fig. [. . . ] C) 1 Peg Perego Primo Viaggio SIP To install the Peg Perego Primo Viaggio SIP you will need the following part(s): 2 ­ Adapter Brackets (1 ­ left, 1 ­ right) 1 ­ U-Shaped Support Bar 1 ­ Spring Support Bar 1 ­ Straight Support Bar 1. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. Before tightening Left Adapter Bracket to frame, align the Straight Support Bar into Adapter Bracket hole. Open the compression locks by flipping the Red Latches up to allow U-Shape Support Bar to be inserted into Adapter Brackets. Insert the U-Shaped Support Bar with the curved end pointing down into the Adapter Brackets. Insert Spring Support Bar into front of U-Shaped Support Bar by squeezing in. Place the car seat onto the U-Shape Support Bar making sure that the Spring and Straight Support Bars engage the locking mechanisms on the Peg Perego car seat. Adjust U-Shape Support Bar to proper length by sliding U-Shape Support Bar in and out. F) 3 Graco/Evenflo Car Seat To install a Graco/ Evenflo car seat you will need the following adapter part(s): 2 ­ Adapter Brackets (1 ­ left, 1 ­ right) 1 ­ U-Shaped Support Bar 1. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. Open the compression locks by flipping the Red Latches up to allow U-Shape Support Bar to be inserted into Adapter Brackets. Insert the U-Shaped Support Bar with the curved end pointing up into the Adapter Brackets. Adjust U-Shape Support Bar to proper length by sliding frame in and out. F) Note: The Straight and Spring Support Bars are not applicable when using a Graco or Evenflo car seat. 4 (Fig. F) 5 Britax Companion Car Seat To install the Britax Companion car seat you will need the following adapter part(s): 2 ­ Adapter Brackets (1 ­ left, 1 ­ right) 1 ­ U-Shaped Support Bar 1 ­ T-Shaped Support Bar 1. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. [. . . ] D) Note: The red compression locks and support bars are not applicable when using the Maxi Cosi car seat. 8 (Fig. D) 9 Thank You! Our #1 goal is to make sure you are happy with our product. If you have any comments or suggestions, we would love to hear from you. 1. 800. 241. 1848 CustomerService@babyjogger. com Baby Jogger is a Division of Dynamic Brands 8575 Magellan Parkway, Suite 1000 · Richmond, VA 23227 T: 800. 241. 1848 · F: 804. 262. 6277 www. babyjogger. com BJC CSA 6. 20. 06 [. . . ]