User manual AVOCET CYCLOMETER 25

[. . . ] You can clear Total Distance manually by holding down the left button in the Total Distance (D) function until the test pattern appears (10 seconds). After no buttons have been pressed and no wheel movement has been detected for 10 minutes, the the clock will display. The normal display returns when a button is pressed or the bicycle is moved. FUNCTIONS 1. Press the right button to move from one function to the next. 4­RIDE TIME­ST 5. [. . . ] Press the right button to switch between miles and kilometers, then complete calibration. You can change between miles and kilometers without erasing stored data. To do this hold the left button in Total Distance (D) for six seconds and release when `mi' or `km' flashes. Stored maximum and average speeds and distance data are automatically converted to the units chosen when you use this method. The calibration number is wheel circumference in millimeters or in inches multipled by 25. 4. Tire Size 20 x 1. 75 24 x 1 600 tubular 650 tubular 26 x 1 26 x 1. 25 26 x 1. 5 Number 1528 mm 1753 1759 1929 1913 1952 1986 Tire Size 26 x 1. 95/2. 0 26 x 2. 1 26 x 1 3/8 700C tubular 700 x 20 700 x 23 700 x 25 Number 2045 mm 2056 2068 2083 2081 2087 2091 Tire Size 700 x 28 700 x 32 700 x 38 27 x 7/8 27 x 1 27 x 1 1/8 27 x 1 1/4 Number 2096 mm 2116 2159 2077 2105 2123 2142 CALIBRATION. Find the calibration number that matches your tire size from the table, or measure tire circumference by the precise calibration method. Hold the left button until the calibration number 2155 shows in the lower display (4 Change the blinking seconds), release, then hold again 4 seconds until the right digit of the digit of the calibration calibration number blinks. To check the calibration number, hold the left button in Trip Distance. After 4 seconds the calibration will appear, and it will remain displayed for 4 seconds after you release the button. PRECISE CALIBRATION. For the most precise calibration, measure the tire's circumference by the following method: Inflate your tires to your usual riding pressure. Mark the ground under the valve stem when the stem is at its lowest point. Get on the bicycle and have a helper push you in your normal riding position until the valve stem returns to its lowest point. Mark below the stem again, then measure the distance between the marks. If you measure in inches, multiply your measurement by 25. 4 to convert to millimeters. Hold down the left button then press the right button to reach clock adjust. You will have to confirm that this digit is correct after you exit clock set. If it is incorrect, return to clock set, go to the left digit, and adjust it again with the right button. Note that you cannot set the clock when the Cyclometer 25 is asleep with only the clock displayed. INSTALLATION STEP 1 ­ TRANSMITTER. Position the receiver magnet housing over a pair of crossed spokes with the spokes inside the slots. Insert the magnet in the well and close the housing pressing the parts together until they lock together over the spokes. Magnet Housing Magnet Spoke STEP 3 - RECEIVER WIRE. [. . . ] After battery installation a blinking "km" appears on the display. Any number other than 2155 indicates improper reset, and the battery must be removed then reinstalled after waiting at least 10 minutes. AVOCET 1-YEAR LIMITED WARRANTY This Avocet Cyclometer is warranted against defects in material and workmanship for one year after date of purchase, or two years after the manufacture date stamped on the PC board under the battery (YM), whichever comes first. The warranty will not cover the battery, normal wear, damage, or loss and is void if the Cyclometer is disassembled by anyone other than an authorized Avocet Service Center. PROCESSING INFORMATION Customer service and product information are available at www. avocet. com/service. html or by calling 650-470-0478. [. . . ]