User manual AVISION IS 15

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] (Each scanned image is given a file name with the prefix img followed by a 4- digit sequential number in the order the images are stored. For example, img0001. jpg, img0002. jpg, etc. ) Note: · Do not remove the memory card or disconnect the power supply while the indicators are blinking. · This scanner only supports output images in JPEG (. jpg) format. · If the memory card is near full (lower than 1MB), the indicator light blinks. · Insert only one original at a time, and insert the next original only when the previous one is done and the blinking has stopped, otherwise the scanner may malfunction. · Remove the things remained on the photo, such as staples, paper clips, and paper sticky notes before feeding it into the scanner due to possible damage to the scanner. 3-3 3. 3 Using Plastic sheaths Always use the clear plastic sheath (included) when scanning photos to ensure the best scanning results. The sheath helps eliminate the possibility of defocusing due to the uneven surface of curled photos. Curled photo 1. Insert the photo into the plastic sheath as shown below. 2. Insert the plastic sheath, flat and level, into the scanner's feeding slot, folded side first, image facing up. Note: · Keeping the original flat and level when feeding prevents possible jamming. · Keep originals free from finger prints, oil, dirt, and dust for optimum scanned image quality. · Remove photos from the plastic sheath after scanning to prevent the sheath from sticking to the photos over time. · If the plastic sheaths are not in use, store them in a safe place and keep them protected from accumulating dust. 3-4 3. 4 Scan dark or night pictures When you need to scan dark or night pictures, be sure to insert your photo into the white plastic sheath to avoid an incomplete scanned image. However, using the white plastic sheath will disable the auto crop (automatic crop your image according to your photo size) and deskew (auto straighten) functions. This means though you have completed scanning your photo, your image may look slightly skew if you have not placed the photo straight in the scanner. . The scanned image using white plastic sheath 3-5 3. 5 Power off the scanner After all originals are scanned, disconnect the supplied power adapter from the scanner. When the scanner connects successfully with a computer, a Removable Disk (F) (F represents the removable drive letter) will be shown in Windows Explorer. If a memory card or flash disk is inserted to the scanner, the Removable Disk will be replaced with the name of the memory card or flash disk. After your scan, a folder titled PHOTO1 is added to the memory card or flash disk and the scanned image will be saved in JPEG file format. Each scanned image is given a file name with the prefix scan followed by a 4- digit sequential number in the order the images are stored. If the file name reaches img9999. jpg in the Photo1 folder, a new folder titled Photo2 will automatically be created to store subsequent new files, and so on. You can now view or edit the files on the memory card or flash disk using your own graphic editing software. 4-2 4. 2 1. 3. Disconnecting the scanner from a computer On the Windows System Tray, click the hardware removal icon. Click the `Safely remove USB mass Storage device' message with the corresponding Drive. [. . . ] Answer: Please insert your photo to the white plastic sheath to get a complete image. Answer: It is normal for the scanner to emit a small amount of heat (around 30-45 Celsius) after prolonged use. However, if there are strange odors coming from the scanner or the scanner feels hot to the touch, disconnect the scanner immediately from the power supply or the computer. 7. 2 The indicator light pattern The indicator light patterns represent function status as follows: Light Steadily on Description The scanner is ready for use. Please wait until the initialization process is complete before using the scanner. [. . . ]