User manual AVISION FB6000E

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - - - - Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION: To assure continued compliance, (example - use only shield interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the manufacture of this device could void the user's authority to operate the equipment. [. . . ] ID# 8 and #9 are not in use. 2. 4 SETTING SCSI TERMINATOR The scanner is equipped with a built-in terminator switch on the rear side of the scanner (See also Figure 2-2). Move the switch to the "on" position to enable the SCSI termination or to the "off" position to disable the SCSI termination. The SCSI termination ensures the electrical signal flow through the SCSI chain properly. As a result, if the scanner is the only or final device connected to your computer, you should enable your SCSI chain terminates at the scanner by moving the terminator switch to the "on" position. If your scanner is linked between the host computer and other SCSI devices, then the SCSI chain should terminate at the final SCSI device. In the case, disable your SCSI termination on the scanner by moving the terminator switch to "off" position. ) 2-3 2 1 1. SCSI Terminator Switch Figure 2-2 SCSI ID setting/Terminator switch 2-4 2. 5 SETTING SCSI SYNC SWITCH The scanner is designed with a SCSI SYNC switch at the rear of the machine. If the SCSI card of your computer supports SYNC, please move the SYNC switch at the rear of the scanner to the "ON" position to make the data transmission faster. ON OFF SYNC Switch Figure 2-3 SCSI SYNC Switch 2-5 2. 6 CONNECTING THE CABLES Be sure the scanner power is switched off. Connect the power cable and SCSI cable as shown in Figure 2-4. Scanner Power cord To a computer SCSI cable To a power outlet Figure 2-4 Cable Connection 2-6 2. 7 PLACING YOUR ORIGINAL Open the document cover then place your original face down on the document glass as shown in Fig. Make sure the top of your original near the document alignment mark. 1 2 3 4 1. Document glass Figure 2-5 Placing the original 2-7 3. SCANNER DRIVER INSTALLATION SYSTEM REQUIREMENTS 3. 1 To run the color image scanner at optimum speed, the following minimum requirements are recommended: · · · · · · · · IBM compatible PC Pentium III 600 or above; Windows 95, Windows 98, Windows ME; One SCSI card installed one your computer; 100M bytes of available hard disk space for installation; 128M bytes of RAM or above; A video graphics array (VGA) monitor; A Microsoft Windows-compatible pointing device (e. g. , the mouse); A CD-ROM drive. 3. 2 1. If the installation menu has not been automatically displayed on your screen, please press the "Start" button and choose RUN, type "d:\cdsetup. exe" ("d:" the CD-ROM drive letter in use). Follow on-screen instructions to complete the installation. 4. 3-1 3. 3 SCANNING WITH IMAGE EDITING SOFTWARE The scanner driver is not a stand-alone program, it has to be started from within a TWAIN-compliant or plug-in software application and then the scanner driver is able to scan and load the image to your computer. The command to start the scanner driver may vary due to different software applications. Start a TWAIN compliant software application such as Roxio PhotoSuite 4 SE which is bundled in the CD. Click Get>Scanner (TWAIN). 3. Choose FB6000E as your scanning source. Allocate your scanned area and choose Scan button to scan the document. 3-2 7. Click Exit to return to the main screen and click Open Library and Photos at the upper-right corner to open your scanned image. 1 2 1. 5. 3 Preview Zoom View Scan Exit Photos 4 5 3-3 3. 4 A GLANCE OF THE USER INTERFACE 7 8 9 10 11 1 2 3 4 5 6 1. Paper Size Choice: Black & White, Halftone, 8-bit Gray, 8bit Color, 24-bit Color. 1 Before Zoom After Zoom 4-6 4. 1. 6 INVERTING AND SELECTING YOUR IMAGE 1. Invert The invert command reverses the brightness and the color in the image. For color images, each pixel will be changed into its complementary color at the command of Invert. 1 2 3 Before Invert After Invert 4-7 2. Mirror Function Reverse the right and left side of your image. Before Mirror 3. After Mirror Auto Select Image Automatically set the whole image as your scan area. [. . . ] Question: While scanning, the scanner often makes noises, or it scans back and forth. Answer: Usually this means the memory of your computer is not enough or the speed of your CPU too slow. Please try to increase your memory to at least 32M or replace your CPU with Pentium or later. Question: Why is it that the scanned image always comes out to be too dark? [. . . ]