User manual AVIOM AVIOM16-O-Y1

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ] It can receive a standard Category 5e cable or a cable fitted with the special heavy-duty EtherCon connector. When using a standard Cat-5e cable, plug the cable into the center of the jack; release the cable by pressing on the small plastic tab built into the cable connector. The locking EtherCon connector is similar to an XLR cable, the kind commonly used on microphones. Insert the EtherCon equipped cable into the jack until it clicks and locks in place. To remove the cable, press on the metal release tab at the top of the panelmounted EtherCon jack and pull the connector outward. Y1 Card Components AVIOM16/o-Y1 Mode Dn/Up - Aviom Up/Dn - 16 ch Up/Up - 8 ch Dn/Dn - Test 1 2 3 4 5 6 7 8 9 10 Stereo Link A-Net Out Made in USA 1 2 3 4 5 1 2 3 4 5 Thumb Screws DIP Switch - Stereo Link DIP Switch - Mode Selection A-Net Output Locking EtherCon RJ45 connector with release tab Installing the Y1 Card The Y1 card can be used in any expansion slot in the Yamaha mixing console. In the Yamaha user interface, the expansions slots are identified by number, starting with "1". Multi-pin connector Align sides of Y1 card with guides in the expansion slot. Thumb screws To install the Y1 card: · Start with the power to the Yamaha mixing console off. · Remove the cover plate on the rear of the Yamaha expansion port to expose the expansion connections. · Slide the Y1 card into place, aligning the sides of the card with the support guides in the expansion slot. · Press the Y1 card firmly in place to attach the multipin card connectors on the Y1 card and Yamaha mixer. · Attach the Y1 card permanently by tightening the two thumb screws on the rear panel of the Y1 card. Note: Aviom suggests using Category 5e (or better) cables when making A-Net connections. DIP Switch The 10-position DIP switch provides two separate functions. The first eight switches are used for controlling the stereo link status of the eight possible audio channel pairs. The last two switches (labeled 9 and 10) provide mode selection control for the Y1 card operation. Dn/Up - Aviom Up/Dn - 16 ch Up/Up - 8 ch Dn/Dn - Test AVIOM1 Mode Mode 1 2 31 42 5 3 6 4 57 6 8 7 9 8 10 9 10 Stereo Stereo Link Link A-Net Out The DIP switch handles shown in the diagrams in this document are illustrated in white. (In the diagram above, for example, switch #10 is in the up position. ) ! Made Stereo Link Switches Positions 1 to 8 of the DIP switch are used for the stereo link function. Stereo linking is possible when using Aviom's Pro16 Personal Mixers for stereo monitoring. When the switch is set to the "On" position (down), the channels are linked as a stereo pair. If the switch is in the "Off " (up) position, the channels are not linked. All connected A-Net devices will instantly update and reflect the change. Compatible A-Net devices that do not respond to stereo linking will not be affected by changes to the link status. The DIP switch 1 to 8 definitions are as follows: · Switch 1 - controls channels 1 and 2 · Switch 2 - controls channels 3 and 4 · Switch 3 - controls channels 5 and 6 · Switch 4 - controls channels 7 and 8 · Switch 5 - controls channels 9 and 10 · Switch 6 - controls channels 11 and 12 · Switch 7 - controls channels 13 and 14 · Switch 8 - controls channels 15 and 16 Mode 1 2 3 4 5 6 7 8 9 10 Stereo Link The example above shows a configuration where channel pairs 3-4, 13-14, and 15-16 are set for stereo operation. Mode Select Switches Positions 9 and 10 of the DIP switch are used for card mode selection. There are four possible switch combinations; three operational modes and one test mode are provided. The Y1 card is scanned during the Yamaha console boot-up procedure only. [. . . ] Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date Purchased . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dealer Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dealer Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Your Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]