User manual AVIOM AV-P2

[. . . ] 1. 00 Certifications ETL/cETL Listed EMC: Conforms to: Certified to: RoHS Status: EN 55013, EN 55020, SAA AS/NZS 1053 IEC 60065, EN 60065, UL 6500-2001 CAN/CSA E60065, KETI Pb-free Notice of Rights All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means--electronic, mechanical, photocopy, recording, or otherwise--without written permission of Aviom, Inc. Trademarks Aviom, A-Net, the A-Net icon, Pro16, and Pro64 are trademarks of Aviom, Inc. Printed in USA WARNING! NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY C~ 00W ! READ THIS FIRST Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] If a replacement power supply is required, always choose a power supply with equivalent specifications: 18-24 VDC, 500mA, center pin positive. 18-24 VDC A-Net Connections Two A-Net connections are provided on the rear panel of the AV-P2 Output Module. The A-Net In port receives digital data in Aviom's proprietary A-Net format. The A-Net Out port is used to pass incoming A-Net data to additional A-Net compatible devices in a system. The A-Net Out port will always transmit the full 16-channel A-Net stream regardless of the settings on the AV-P2. LEFT AUDIO OUTPUT RIGHT AV-P2 OUT IN Audio Outputs Audio outputs on the AV-P2 are provided via locking Euroblock connectors. Each channel's output level can be set individually using the DIP switches on the front panel. DC POWER 500mA +­ +­ The AV-P2 rear-panel A-Net connections Connecting Audio The audio outputs on the AV-P2 Output Module can be connected to balanced or unbalanced devices via the Euroblock jacks. Wiring a Euroblock Euroblock connectors provide an easy, solder-free way of making audio connections between the AV-P2 and other audio components. For extra strength, you can add solder to each bare wire on an audio cable to stop the wire strands from unwinding (called "tinning"). The Euroblock plug, showing the screws that hold the individual wires in place (left-to-right), hot (+), cold (-), and ground Connecting to an Unbalanced Device The AV-P2 audio outputs can be connected to unbalanced audio devices; connections can use single-conductor or two-conductor shielded cable. IN 18-24 VDC DC POWER 500mA LEFT AUDIO OUTPUT RIGHT AV-P2 OUT Single-conductor shielded cable To connect the AV-P2 audio output to an unbalanced line-level device using single-conductor shielded cable: 1. Strip the insulating jacket of the cable back about . 75 inch (18 mm) to reveal the individual hot and ground wires within. Remove a small amount of each individual wire's insulation (approximately . 25 inch, 6 mm). On the Euroblock plug, use a small screw driver to loosen and open the sockets that will receive the individual wires. Insert the audio cable's hot (+) wire into the matching socket on the Euroblock plug. Insert the audio cable's ground wire into the matching socket on the Euroblock plug. The cold (-) socket on the Euroblock remains unused in this configuration. Tighten the screws on the wire sockets to secure the individual wires. Plug the completed Euroblock plug into the desired output channel on the AV-P2. Connect the completed cable to your audio device. +­ +­ AV-P2 left/right Euroblock audio outputs Connecting to a Balanced Device To connect the AV-P2 Euroblock audio output to a device that can accept a balanced line-level input: 1. Strip the insulating jacket of the cable back about . 75 inch (18 mm) to reveal the individual hot, cold, and ground wires within. Remove a small amount of each individual wire's insulation (approximately . 25 inch, 6 mm). On the 5. 0 mm Euroblock male plug, use a small screw driver to loosen and open the sockets that will receive the individual wires. Insert the individual hot (+), cold (-), and ground wires into the matching sockets on the Euroblock plug. Tighten the screws on the wire sockets to secure the individual wires. Plug the completed Euroblock plug into the desired output channel on the AV-P2. 7. Two-conductor shielded cable To connect the AV-P2 audio output to an unbalanced line-level device using two-conductor shielded cable: 1. Strip the insulating jacket of the cable back about . 75 inch (18 mm) to reveal the individual hot and ground wires within. [. . . ] Connect 16 mic- or line-level audio sources to inputs 1-16 on the first Pro16 Series input module. Connect a Cat-5e cable from the A-Net out port on the first input module to the A-Net expANsioN port on the first output module. Plug a Cat-5e cable into the A-Net iN port on the first output module. This cable will be used to span up to 500 feet/150 meters between the two sides of the network. [. . . ]