User manual AVANTI WDP69 INSTRUCTION MANUAL

[. . . ] It lists causes of minor operating problems that you can correct yourself. 3 PARTS AND FEATURES 1. 14. STORAGE COMPARTMENT HOT WATER DRAIN POWER CORD CONDENSER COILS HEATING SWITCH (RED) COOLING SWITCH (GREEN) LEGS 4 Important Safety Instructions ? ?? WARNING? To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions: Read all instructions before using the water dispenser. Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other water dispenser. [. . . ] 80º C (176º F), the red indicator will glow again and another heating process starts. Continue holding safety button while pushing in faucet as long as water is being dispensed. When faucet is released, make sure to return it to the original position. ?Cup Dispenser (Optional) A cup dispenser may be installed by using the mounting holes (covered with plastic caps) located near the top of the right side panel of the cooler. The cup dispenser comes equipped with a mounting bracket and screws and may be ordered by completing the enclosed order form provided with your instruction manual. CARE AND MAINTENANCE ?Wash the inside of the reservoir with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. The drip tray and water faucets should be cleaned with mild detergent and warm water. At regular intervals or once a month inspect the coils located across the back of the dispenser. Vacuum accumulation of dust or clean it with a hard brush. TAKING DISPENSER OUT OF SERVICE ?If the water dispenser will not be used for a long period of time, unplug the power cord from the wall outlet. Turn the switch marked "HOT" to the "OFF" position. Drain the water from the tanks by removing the plug from the back of the dispenser. WARNING--THE WATER COMING OUT OF THE BACK SIDE MARKED "HOT" MAY BE SCOLDING. ? Unit should not be transported on the sides. Place it upright if possible and cover it with a blanket. Installation instructions on how to secure your Avanti unit to the wall 7 1- Attach the mounting brackets provided, into the pre-drilled holes located at the back of the unit side panels (see picture 2A) by using the self-tap screws provided. 2- After both brackets are properly installed, use the other end of the bracket to assist in aligning the holes to be drilled on the wall as follows: Measure the center of the bracket mounting hole and the ground (see picture 2A), and measure the distance between the center of both brackets mounting holes (see picture 2B). Both of the above measurements will give you the exact location for drilling the holes on the wall where the unit will be secured. 3- Please be aware that when securing these brackets to the wall, different types of bolts may be used, depending on the different types of wall construction (these bolts are not included). If you are not able to obtain the measurements as explained above, you can also mount and secure both brackets to the unit. Move the unit to your desired location and mark the wall using the holes at the other end of the bracket. 8 PROBLEMS WITH YOUR WATER DISPENSER? You can solve many common water dispenser problems easily, saving you the cost of a possible service call. Try the suggestions outlined below to see if you can solve the problem before calling the servicer. TROUBLESHOOTING GUIDE PROBLEM Water dispenser does not operate. The rattling noise may come from the flow of the refrigerant, which is normal. As each cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your water dispenser. [. . . ] ? 13 INSTRUCCIONES PARA ASEGURAR SU UNIDAD AVANTI A LA PARED 1- DETRAS DE LA UNIDAD HAY UNAS PERFORACIONES PARA LA INSTALACION DE SOPORTES LATERALES, USANDO TORNILLOS (VEA FIGURA 1). 2- DESPUES DE INSTALAR AMBOS SOPORTES, USE EL EXTREMO DEL SOPORTE PARA OBTENER LAS SIGUIENTES MEDIDAS: MIDA LA DISTANCIA ENTRE EL PISO Y EL CENTRO DEL HUECO DEL SOPORTE YA PREVIAMENTE INSTALADO (VEA FIGURA 2A). MIDA LA DISTANCIA QUE EXISTE ENTRE EL CENTRO DE LOS HUECOS DE LOS DOS SOPORTES (VEA FIGURA 2B). AMBAS MEDIDAS LE DARAN EXACTAMENTE LA LOCALIZACION PARA BARRENAR Y ASEGURAR SU UNIDAD A LA PARED ESCOGIDA. [. . . ]