User manual AUDIOVOX VOD710

[. . . ] POWER PLAY STOP EJEC T VOD705 VOD710 DROP-DOWN VIDEO MONITOR WITH BUILT-IN DVD PLAYER ON OFF AUTO ® ELECTRONICS CORP. 128-7034 Date: 12/05/2003 Date: 21/5/2003-PROV710 S & PROV710 P ADDED Date: 28/5/2003-page7: The DVD Player Perform changed 128-7034 1 of 26 IMPORTANT An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in `park' or when the vehicle's parking brake is applied. An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied, must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Warnings !Do not use any solvents or cleaning materials when cleaning the video monitor. [. . . ] In this case you must use the remote control supplied with the component. POWER PLAY STOP EJEC T ON OFF AUTO Remote Sensor Accessories Wireless Headphones The VOD710 includes a built-in infrared transmitter for use with Audiovox wireless headphones (Part Number MVIRHS). The wireless headphones must be used within a line of sight from the transmitter, as infrared transmissions, like visible light travel only in a straight line. Headset Special Features · Automatic Level Control prevents input signal over loading. · Uses high frequency infrared light to assure a clean signal for clear reception. -13- 128-7034 13 of 26 AV1 This video input may be connected to a Video cassette Player (VCP), video game system, or other audio / video device. To access the A/V input, turn the VOD710 on and press the source select button on the VOD710 or the Source button on the remote control until "AV1" is displayed on the screen. Turn the video source component on with its power button or remote control. The VOD710 is now ready to play the audio and video signals from the source connected to the AV1 input. Video Out The VOD710 provides a video output for an optional video monitor(s). (Refer to the Installation Guide for more details. ) This output will provide a video signal that duplicates the signal displayed by the VOD710 to an additional monitor or video display. The user can select either English, French or Spanish for the OSD language. ) buttons, and then press the ENTER button. -16- 128-7034 16 of 26 Settings for Display Press the SETUP button and select Display. The DISPLAY SETUP allows you to adjust screen setting (aspect ratio) Press and then use the ( )buttons to select the appropriate settings. 4:3 / PS This displays the wide picture on the screen with a portion of the left & right side removed. 4:3 / LB This displays the wide picture with black bands on the upper and lower portions of the screen. 16:9 This displays a picture with black bands on the upper and lower portion of the screen. The DEFAULTS SETUP allows you to reset ALL options to the factory default Settings. Press and then press Enter to implement the reset function. -17- 128-7034 17 of 26 Settings for Parental (Parental Control) This section of the SETUP Menu allows user to control the content of movie playback from G to NO_PARENTAL. The Parental Control function allows you to limit viewing to your preference. Use the G (Children) PG PG 13 R NC-17 ADULT (Adult) NO_PARENTAL (No Parental Control) Note:The lower the value, the more strict the limitation. Press the Enter button to confirm the selection. Input a password in 4 digits using the numeric buttons then press the Enter button. The Default password is 3308. -18- 128-7034 18 of 26 Settings for Password (Parental Control Password) Press the SETUP button and select PASSWORD. The PASSWORD SETUP allows you to change the parental control password. [. . . ] · Make sure Modulator is ON and the proper Frequency has been selected. · Verify that the remote sensor eye is not obstructed. · Verify that the infrared transmitter is affixed over the sensor eye of the component to be controlled. Disc won't play · Insert a disc with the label side facing up. If the regional codes don't match, the disc can't be played. Allow player to dry out. Can't advance through a movie · You can't advance through the opening credits and warning information that appears at the beginning of movies because the disc is programmed to prohibit that action. [. . . ]