User manual AUDIOVOX VE706 Operation Manual

[. . . ] VE706 LOW PROFILE TELEVISION INSTALLATION AND OPERATION MANUAL · · · · · Multi-function Remote Control Cable Ready 125 Channel TV Tuner Internal Stereo Speakers Under Cabinet / Table Top Mounting AM/FM Radio Tuner 0 INTRODUCTION WARNING ­ To prevent fire or shock hazard, do not expose this unit to moisture. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). TO QUALIFIED SERVICE CAUT ION This symbol is intended to alert the user to the presence of uninsured "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. TO PREVENT ELECTRIC SHOCK: DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. 1 INFORMATION This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacture's instructions, may cause or receive unwanted interference. This unit complies with FCC Rules Part 15, which are designed to provide reasonable protection against interference in a residential installation. [. . . ] Be sure that the location chosen will provide adequate access to the electrical connection on the rear of the unit before continuing. 2) If the location chosen has a bottom edge molding it may be necessary to use the mounting spacers provided to effectively lower the VE706 below or even with the molding. Measure the distance between the edge molding and the bottom of the cabinet. The spacers and mounting holes are stepped to achieve different mounting heights from . 5" to 1". Adjusting the mounting height is done by lifting and rotating the spacer in the mounting hole. Choose a spacer height, which will allow the VE706 to clear the edge molding. 3) Measure the thickness of the bottom of the cabinet or shelf and the spacer height chosen. Select the shortest screw length, which will secure the VE706 to the bottom of the cabinet. 4) Cut out the template supplied and tape it in place onto the cabinet surface to be drilled. Center punch four holes indicated on the template and remove the template. the 5) Carefully drill four 1/8 holes at the locations marked above. Place the screws selected through the VE706 and then through the spacers (if required from the bottom-up) 6) 7) 8) 9) Connect your TV antenna or cable system to the antenna connector on the rear of the VE706. TV BUTTON ­ Press this button to select TV mode and Press and Hold this button to change the aspect ratio. MUTE BUTTON ­ Press this button to mute the audio (++++ will appear and blink on the display when the system is muted). 10) P4 - BUTTON ­ Selected Preset Channel "4" in the Radio or TV mode 11) P3 - BUTTON ­ Selected Preset Channel "3" in the Radio or TV mode. 12) P2 - BUTTON ­ Selected Preset Channel "2" in the Radio or TV mode. 13) P1- BUTTON ­ Selected Preset Channel "1" in the Radio or TV mode. 15) VOLUME DOWN ( ) BUTTON ­ Press this button to lower the volume. 16) SEEK BUTTONS ( 17) CHANNEL BUTTONS ( -Right Side) ­ Press these buttons to go to next available channel with -Left Side) ­ Press these buttons to go to next available channel. 18) DISPLAY WINDOW ­ Displays the channel/station number, time, and selected source. 19) REMOTE INFRARED SENSORS-These sensors receive infrared command signals from the hand held remote control unit. 10 REAR PANEL CONNECTIONS 1 2 3 4 1) 2) 3) 4) AC LINE CORD ­ Connects to AC power outlet. FM ANTENNA ­ Allows the VE706 to be connected to a 75-Ohm external coaxial antenna for the reception of FM broadcast signals. AM ANTENNA - Allows the VE706 to be connected to an external antenna for the reception of AM broadcast signals. TV ANTENNA (75 OHM ANTENNA CONNECTOR) -Allows the VE706 to be connected to a 75ohm external coaxial antenna or cable TV system. 11 LCD Control Functions 1. Highlight the menu item to be changed using the UP/DOWN buttons and then press Select to adjust the highlighted item. . UP Button ­ Scrolls upward through menu items, also adjusts selected item in upward (increase) direction. DOWN Button ­ Scrolls downward through menu items; also adjusts selected item; in downward (decrease) direction. [. . . ] When setting the alarm, check the AM/PM indicator to assure the proper setting. Once the alarm is set it will sound each day at the same time as long as it is activated. DEACTIVATING ALARM 1) Press the SET button twice to enter the alarm mode. The set time will disappear from the Display Window and a series of dashes (--: --) will appear, Alarm DEACTIVATED mode. [. . . ]