User manual AUDIOVOX VE700

[. . . ] External Accessories ­ Do not use external accessories not recommended by the product manufacturer, as they may cause a hazard. Water and Moisture ­ Do not use this product near water ­ for example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or similar situations. Mounting considerations ­ Do not place this product on an unstable cart, stand, tripod bracket, or table. The Product may fall, causing serious injury to a child or adult, and serious damage to the product. [. . . ] 5) Do not overload electrical outlets or use extension cords as this can result in risk of fire or electric shock. 6) Never push objects of any kind into this unit though openings as they may touch dangerous voltage points or short-circuit parts that could result in a fir or electric shock. 7) Do not attempt to service the VE700 yourself as opening or removing covers may expose you to dangerous voltage or other hazards. 8) Unplug the VE700 from the outlet and refer servicing to qualified service personnel under the following conditions: a) If the unit has been exposed to water. b) If the does not operate normally when following the operating instructions. c) If the unit has been dropped or the cabinet has been damaged. - Cable System Installation: Note to CATV system installer: "This reminder is provided to call the CATV (CABLE-TV) system installer's attention to article 820-40 of the NEC, that provides guidelines for proper grounding and, in particular, specified that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical" - Under cabinet mounting: " CAUTION: to reduce the risk of fire, do not place any heating or cooking product beneath this unit" -7- CONTENTS OF PACKAGE PW R TEL TV VO L C H EN T CH VO L A /V M UTE SEEK F M /A M 1 4 7 2 5 8 3 ERA SE 6 9 ADD 0 1. Manual -8- UNDER CABINET INSTALLATION 1) Choose an appropriate mounting location underneath a cabinet or shelf. Close proximity to an electrical outlet, a TV antenna or cable connection and a telephone jack will facilitate a neat, easy installation. Be sure that the location chosen will provide adequate access to the electrical connection on the rear of the unit before continuing. 2) If the location chosen has bottom edge molding it may be necessary to use the mounting spacers provided to effectively lower the VE700 below or even with the molding. Measure the distance between the bottom and the bottom of the cabinet. For large molding choose a combination of spacers which will allow the VE700 to be secured to the bottom of the cabinet. 3) Measure the thickness of the bottom of the cabinet or shelf and the spacers chosen. Select the shortest screw length, which will secure the VE700 to the bottom of the cabinet. 4) Cut out the template supplied and tape it in place onto the cabinet surface to be drilled. Center punch the four holes indicated on the template and remove the template. Place the screws selected through the VE700 and then through the spacers (if required from the bottom-up) 6) Position the VE700 and mount it in place using the selected screws. 7) Connect your TV antenna or cable system to the antenna connector on the rear of the VE700. 8) Attach the FM Dipole Antenna to the FM Antenna screws and position the antenna for the best reception. 9) If using the speakerphone feature, plug the VE700 into a phone jack. 12) Remote Infrared sensor-This sensor receives infrared signals from the hand held remote control unit. 13) LCD Display ­ Displays the channel number, AM/FM frequencies, the time of day and auxiliary input. [. . . ] 3) Each time CH up/down button is pressed it will select different tone. SETTING THE CABLE TV MODE 1) Press the SET button three times to enter the cable configuration mode. 3) Press the CH up/down button to select the cable mode (STD/IRC/HRC). 4) When the desired mode is reached, press the PWR button or T/F button to confirm. - 17 - SETTING THE AIR TV MODE 1) Press the SET button three times to enter the cable configuration mode 2) Press the SEEK button to select the AIR mode AIR appears on the display (switched from broadcast TV (VHF or UHF) to cable TV). [. . . ]