User manual AUDIOVOX PROVE8

[. . . ] VOD705 P OW ER E JE C T RE V P LAY FWD STOP PROVE8 VO LU ME CH A N N EL AU T O S OU RC E P ROG RA M S E LE C T PIC T URE S E LE C T ON OFF AUT O 8" LCD OVERHEAD TV/MONITOR WITH DVD PLAYER HEADPHONE S AUDIO IN PUT VIDEO IR L R ® ELECTRONICS CORP. 128-6700 IMPORTANT An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in `park' or when the vehicle's parking brake is applied. An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied, must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Warnings !Do not use any solvents or cleaning materials when cleaning the video monitor. [. . . ] Wireless Headset Special Features · Automatic Level Control prevents input signal over loading. · Uses high frequency infrared light to assure a clean signal for clear reception. , 5 L R Wired Headphones There are two 1/8" headphone jacks on the PROVE8 that can be used with any standard wired stereo headphones. These jacks are controlled by the volume up / down buttons on the PROVE8 remote control. Wired FM Modulator The PROVE8 is equipped with an RF modulator, that allows you to listen to the PROVE8 audio signal by tuning your vehicle's radio to the selected frequency, (88. 3, 88. 7, 89. 1, 89. 5, 89. 9 MHz). This feature is accessed by using the FM transmitter buttons on the remote (On/Off, Select). Whenever the RF modulator is on, broadcast reception on the vehicles radio will be poor. AV1 The video inputs may be connected to a Video cassette Player (VCP), video game system, or other audio / video devices. To access the AV1 inputs, turn the PROVE8 on and press the source button on the PROVE8 or the Source button on the remote control until "AV1" is displayed on the screen. Turn the video source component on with its power button or remote control. The PROVE8 is now ready to play the audio and video signals from the source connected to AV1 input. AUX A video game system, Camcorder or other audio/video device may be connected to the AUX input jacks (see Figure 1. To access the AUX source, turn the PROVE8 or the Source button on the remote control. The PROVE8 is now ready to play the audio and video signals from the source connected to the AUX input. IR2 Any pre-amp level (CD Changer, Satellite Radio, etc) audio source may be input into the second IR input. When using Audiovox headphones (part number IR2CHS) simply switch to channel B to listen to the source connected to the second IR input. DVD Basics To get the optimum use out of the DVD section, make sure you read this section completely. Regional Coding Both the DVD player and disc are coded by region. The unit will display "WRONG REGION. " Types of Discs your DVD will play · DVD discs ­ DVDs discs which contain video. · Audio discs ­ Audio CDs contain musical or sound content only. · MP3 discs ­ A disc that contains audio files (for example, a CD-R with downloaded MP3 files). Loading and Playing Discs Before you load a disc, make sure that it is compatible with the player. Note: the following Discs CANNOT be used with this player : · MiniDisc · Laserdisc · CD-I, CD-ROM, DVD-ROM To load and Play a Disc When you press the Power button the unit will turn on and display the source selected. When the disc is half way in it will be automatically pulled in and change the source to DVD mode and start the playback. Settings and Adjustments This chapter describes how to set and how to adjust using the on-screen SETUP menu. Using the Setup Menu Using the setup display, you can do the initial setup, adjust the picture quality, and set the various outputs. You can also set a language for the on-screen display and the setup display and limit play back by children. 1) Press the SETUP button to display the "setup menu" on the TV screen. [. . . ] · If you are using the IR headphones, make sure you turn on the IR power. · Make sure Modulator is ON and the proper Frequency has been selected. · Verify that the remote sensor eye is not obstructed. · Verify that the infrared transmitter is affixed over the sensor eye of the component to be controlled. Disc won't play · Insert a disc with the label side facing up. If the regional codes don't match, the disc can't be played. [. . . ]