User manual AUDIOVOX LCM641TV INSTALLATION

[. . . ] If any access holes need to be cut into the vehicle (headliner, other trim components, etc. ) this should be done now as well. (Refer to the wiring diagrams on pages 6 and 7 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. [. . . ] 2) Mounting location and method for the individual components will vary from vehicle to vehicle, so this manual will only focus on the installation of the video pod itself and related console accessories. 3) Generally, the best location for the video pod is where the vehicle' dome s light is traditionally installed (center of roof, just behind the front 2 seats). The pod should be located in such a manner that it can be comfortably viewed by the rear seat passengers in the vehicle. The pod should NEVER be located in a position that would place it in within the driver' field of view. This is not s only hazardous for driving conditions (as it creates a distraction to the driver), but it is against the law in many states. 4) Once pod location has been determined, there may be prep work required for the headliner. Some of the steps that may need to be taken depending upon your installation are: a) Removing of the vehicle' dome light. s b) The headliner MAY have to be cut out per the diagram below. ** c) If the mini-console is being used, it will have to be trimmed to fit the contour of the headliner. you may have to do none, some, or all of these steps. ** IF your particular installation will require you to cut out the headliner, the box that this kit came in can be used as a template. You can remove the shelf that the video pod rests upon and trace the opening onto the headliner for cutting. Figure 2 Page 5 of 11 P/N 8010845 Rev. F Nov. 00 Wiring Diagram Hook Up Procedure: Figure 3 1) Insert the circular mini-din connector of the source component harness through wire tie loop on the main PCB and into mini-din connector on main PCB (fig. 3). 4) Connect power harness to vehicle' electrical system s by tapping into an accessory hot line. 5) Verify all functions of system before final mounting of finished assembly. Black: Ground Red: +12 VDC (Accessory Cir. ) TV antenna (If applicable) Mini din connector (Source Component harness) Wire tie Loop Mini-DIN Receptacle Figure 4 Power Harness Item # 3a Power Connector (2-pin) Antenna Connector Optional Remote Headphone Stations Stereo Headphone Jack Spade Terminals Green (Right+) Spade Terminals Black (Ground) A/V Source definitions: 1 = Tuner 2 = VCP (left mini-din on main PCB 3 = 2nd VCP (right mini-dIn on main PCB for game, future DVD, etc. Note: AUX Input overrides 2nd VCP (DIN) Input when connector is plugged into RCA jack Stereo Headphone Jack Spade Terminals Gray (Left+) Page 6 of 11 P/N 8010845 Rev. F Nov. 00 Source Component Harness Hook-Up: Figure 5 A second VCP or other A/V component can be connected to video monitor system using a second source component harness (purchased separately, P/N 8010730). This second harness would plug into second Mini-Din connector on main PCB as in steps 1 and 2 above. Video Out (Yellow) Yellow RCA (Video In) Right Out (Red) Left Out (White) White RCA (Audio In Left) Red RCA (Audio In Right) Source Component Harness P/N 8010730 Power Connector (4-pin) "Y" Adapter for use with Non-Stereo Installations P/N 0892165 IR LED: Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Window on the Face of the VCP. VCP (Rear View) Page 7 of 11 P/N 8010845 Rev. F Nov. 00 Mini Console Installation: This page only covers special installation considerations for the mini-console installation. If video pod is to be installed with a custom full sized overhead console, skip to page 9 now. If video pod is to be installed in a vehicle with mini-console (P/N 1181300), this console may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video pod is mounted directly to overhead cross member in roof using mounting screw bosses (Item c on page 3). These screw bosses should contact the cross member directly (ie: No gap between the screw boss and roof structure). [. . . ] d) Check fit of trimmed console and make any minor adjustments necessary. 4) The mini console can be painted or covered with a material that matches headliner before assembling mini console to the video pod. 5) The finished mini console should be attached to video pod, then attach assembly to roof. See figure 7. Headliner Cut Line Lowest Point Mark Page 8 of 11 P/N 8010845 Rev. F Nov. [. . . ]