User manual AUDIOVOX FPE2306

[. . . ] Use only a trolley, stand, tripod, and bracket or table recommended by the manufacturer or sold with the product. 5 This TV set operates on power of 120V, 60Hz. You must not use a power supply of any other type. When relocating the product placed on a trolley, it must be moved with the utmost care. Sudden stops, excessive force and uneven floor surfaces can cause the product to fall from the trolley. The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Powersupply cords should be routed so that they are not likely to be walked on or snagged by items placed upon or against them. [. . . ] Please note: An RF switch provided with two inputs (A and B) is required (not supplied). RF switch (not supplied) Two-set signal splitter (not supplied) OUT IN Cable TV converter/ descrambler (not supplied) Cable TV Line "A" position on the RF switch (not supplied) : You can view all unscrambled channels by using the TV's channel keys. "B" position on the RF switch (not supplied) : You can view the scrambled channels via the converter/descrambler by using the converter's channel keys. Note: Consult your Dealer or Service Center for the type of splitter, RF switch or combiner that might be required. ANTENNAS The antenna requirements for good color television reception are more important than those for black & white television reception. For this reason, a good quality outdoor antenna is strongly recommended. The following is a brief explanation of the type of connections that are provided with the various antenna systems. A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (not supplied). A 300-ohm system is a flat "twin-lead" cable that can be attached to a 75-ohm terminal through a 300-75-ohm adapter (not supplied). F-type connector 75-ohm coaxial cable (round) 300-ohm twin-lead cable (flat) OUTDOOR ANTENNA CONNECTION Use one of the following two diagrams if you connect an outdoor antenna. Combination VHF/UHF Antenna 300/75-ohm adapter (not supplied) or 300-ohm twin-lead VHF/UHF antenna 75-ohm coaxial cable Antenna cable B. Separate VHF and/or UHF Antennas UHF antenna VHF antenna VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L R L HDTV AV 300-ohm twin-lead Combiner (not supplied) OUT IN 300-ohm twin-lead 75-ohm coaxial cable or 12 Installation Power connection Before using this equipment, please connect the AC power adapter correctly. VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L R L HDTV AV - + Household power outlet Plug into AC outlet. AC cord AC power adapter 1. Connect the male plug to the wall outlet as illustrated. Notes: + This product should be operated only from the type of power source indicated on the marking label. + Always unplug the AC adapter from the product and power outlet when not using for a long period of time. 13 Installation(continued) Connecting video/audio equipment VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V +12V +5V ANT IN PHONE LINE IN R L R L R L HDTV AV Y Yellow (video) W white (audio L/MONO) R red (audio R) To S-video input R W To audio Y inputs To video input R w To audio inputs w R To audio outputs VHS To video output Y To audio outputs w R Video equipment with S-video terminal VHS To ANT output Video equipment without S-video terminal To ANT output 14 To ANT input Installation(continued) Connecting DVD player and speakers VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V +12V +5V ANT IN PHONE LINE IN R L R L R L HDTV AV Red To speaker Black Red To YCbCr G inputs B R R w To audio inputs To speaker To YCbCr outputs G B R R w To audio outputs DVD DVD Player W White (audio L/MONO) VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L R L R G B Red (audio R, Cr) Green (Y) Blue (Cb) HDTV AV 15 Installation(continued) Connecting YPbPr terminals VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V +12V +5V ANT IN PHONE LINE IN R L R L R L HDTV AV To YPbPr inputs G B R R w To audio inputs W White (audio L/MONO) Red (audio R, Pr) Green (Y) Blue (Pb) R G B To YPbPr outputs (480p/720p/ 1080i) G B R R w To audio outputs SET TOP BOX (Or other equipment with YPbPr output terminals) 16 Installation(continued) Connecting VGA interface VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V +12V +5V ANT IN PHONE LINE IN R L R L R L HDTV AV To LINE in To VGA input interface Equipment with VGA output interface To LINE out To VGA output interface 17 Installation(continued) Elevation adjustment You can adjust the angle of the LCD TV as follows. To resume the sound, press this button again or you can also press VOL+ or VOL- to resume the sound. * To exit the menu, press ENTER button. 25 System setup SETUP Color sys Language OSD position OSD background AUTO Eng Upper Left Opaque To enter into SETUP menu 1. Press VOL+ or VOL- button to confirm or adjust selected item. <LEFT> or <RIGHT> key to change Color system In AV mode, you can select color system. Press VOL- or VOL+ button to select a proper color system according to the program type. Normally, select AUTO. SETUP Color sys Language OSD position OSD background AUTO Eng Upper Left Opaque <LEFT> or <RIGHT> key to change You can quickly access Color system menu bar by C. SYS *This is an advanced setting and should not be touched. Setting OSD Language SETUP Color sys Language OSD position OSD background AUTO Eng Upper Left Opaque From the SETUP menu, press CH5/6to select Language item. Press VOL- or VOL+ button to select the desired language. <LEFT> or <RIGHT> key to change * To exit the menu, press ENTER button. 26 System setup(continued) SETUP Color sys Language OSD position OSD background AUTO Eng Upper Left Opaque Setting OSD position From the SETUP menu, press CH5/6to select OSD position item. Press VOL- or VOL+ button to select an OSD position in your preference. <LEFT> or <RIGHT> key to change Notes: You can quickly select OSD menu position by using OSD POSITION button on the remote. Setting OSD Background From the SETUP menu, press CH5/6to select OSD Background item. Press VOL- or VOL+ button to select Opaque or Translucent. Color sys Language OSD position OSD background SETUP AUTO Eng Upper Left Opaque <LEFT> or <RIGHT> key to change Setting Scaler mode This unit allows you to adjust screen aspect ratio in your preference. Press ZOOM button on the remote to select a proper screen aspect ratio. Anamorphic, 4:3 and Panorama can be selected. Anamorphic Notes: You can quickly select screen ratio by using ZOOM button on the Remote Control * To exit the menu, press ENTER button. 27 Timer setting Use SLP button Press SLP button repeatedly to set sleep time between: 0, 10, 20, 30, 60, 90, 120, 180, 240 minutes. If you select 0 minute, it means the sleep timer function is turned off. Turn off 0 Use CLK button Press CLK button, the Current time menu bar appears. Use CH5/6 to select hour or minute (the selected item is displayed in white), use VOL+/- to set the current time. Current time 0:40 28 CCD setting To enter into CCD and Vchip SETTINGS menu 1. [. . . ] Connect the YPbPr terminals to Set Top Box and make sure there is signal input. Adjusting picture In YPbPr mode when there is correct input signal, press MENU button and PICTURE SETTING menu appears. Use CH5/6to select item and VOL+/- to adjust. Item Brightness Contrast Saturation Sharpness VOLdarker weaker paler softer VOL+ lighter stronger deeper sharper PICTURE SETTING Brightness Contrast Saturation Sharpness Color Temp 25 25 25 25 9300K <LEFT> or <RIGHT> key to change Adjusting Color temperature PICTURE SETTING You can select different Color temperature to obtain correct white. Press MENU button, use CH5/6 to select Color Temp item, press the VOL+/- to select between Brightness Contrast Saturation Sharpness Color Temp 25 25 25 25 9300K <LEFT> or <RIGHT> key to change Adjusting horizontal / vertical position Press MENU button twice and the PICTURE POSITION menu appears. Use CH5/6 to select item and VOL+/- to adjust. When nonstandard signal input to the set and the picture may not be in the screen center. [. . . ]