User manual AUDIOVOX CE531MP

[. . . ] Press the MP3 MODE button once the " " will blink, the file name and the number's tracks appear on the display. Press the SKIP/SEARCH / buttons one by one to find the file name, the file name will display sequence as "A, B . . . . . . . . . . . Press the SKIP/SEARCH / buttons about 2 seconds, the capital letters or the figure will blinks. If the first letter of the file name in this disc haven't the capital letters or the figure, it will not blink. [. . . ] · If an abnormal display indication or an operating problem occurs, disconnect the AC power cord. · Before transporting the unit, remove the disc from the CD tray. VENTILATION WARNING · Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc. , the heat may not be able to get out. ) USING THE REMOTE CONTROL CORRECTLY · Point the Remote Control at the REMOTE SENSOR located on the unit. · When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded, causing unreliable operation. · The recommended effective distance for remote operation is about 6 meters (19 feet). RATING PLATE LOCATION The rating plate location is on the bottom of product. Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel. TROUBLE SHOOTING TIPS Problem System does not turn on ON SAFETY · When connecting and disconnecting the AC cord, grip the plug and not the cord itself. · When you are not going to use the unit for a long period of time, disconnect the AC power cord. · When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off. · When the AC power cord is connected, the standby indicator will light up. Solutions · Make sure AC power plug is secure in the outlet, and outlet has power. · Electrical interference in your home can cause poor reception. Move the unit away from sources of interference (especially those with motors and transformers). · Set the AM/MW loop antenna to a direction for the better reception. TO CHANGE REMOTE BATTERY Take out the PVC sheet before operating the Remote Control. CD/MP3 1. Insert one CR2025 (3V) size battery. ATTENTION Disc in place but unit won't play SPECIFICATION GENERAL Power consumption: Output power: Power source: 65W 30W x 2 (10% THD) AC ~120V 60 Hz (USA and Canada) AC ~220V 50 Hz (China) AC ~230V 50 Hz (Europe) AC ~240V 50 Hz (Australia) AC ~110-120V/220-240V 50/60Hz (Others) NOTES ON BATTERIES · When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. Disc skips BATTERY REPLACEMENT When battery become weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the battery. Poor FM reception ON AC VOLTAGE · Before use, check that the rated voltage of your unit matches your local voltage. RADIO NOTE : If the Remote Control is not to be used for a long time, remove the battery to avoid damage caused by battery leakage corrosion. WARNING : Do not dispose of batteries in fire, batteries may explode or leak. Replace only with the same or equivalent type. FCC INFORMATION This device complies with part 15 of FCC Rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, and Specifications may be subject to change without notice. Poor MW reception Printed in China 811-6938A1-010 PARTS IDENTIFICATION 1. SKIP button 1 CONNECTIONS 1 RIGHT SPEAKER BOX LEFT SPEAKER BOX TURNING ON THE UNIT TO TURN ON THE UNIT Press the STANDBY/ON button, the indicator will turn off. Select the desired function and the corresponding function indicator will light up. TIMER OPERATION TIMER PLAY AND TURN OFF THE UNIT AUTOMATICALLY The power can be turn on or turn off automatically at a preset time. Make sure the time which use to turn on or turn off is correct, please refer to CLOCK setting procedure. 1. Press and hold SLEEP/TIMER button for about 3 seconds until the " " and "on" indicators will on the display and the hour will blinks on the display. Press the SLEEP/TIMER button, the "off" indicator will on the display and the hour will blink on the display. Press the SLEEP/TIMER button, the "TUNER" will blink on the display. [. . . ] Repeat steps 1 to 4 for the next preset. Locating a particular point in a track To move backward at high speed button pressed Keep the SKIP during play and release at the desired point. To move forward at high speed button pressed Keep the SKIP during play and release at the desired point. Searching for the beginning of a track To find a previous track button once to Press the SKIP return to the beginning of the current track. To skip tracks button repeatedly Press the SKIP to skip track(s) forward one by one. TUNING INTO A PRESET STATION Fully unwind the wire antenna. Then extend the wire antenna and place it in the position that sounds best. [. . . ]