User manual AUDIOVOX AVT-988

[. . . ] 9" COLOR TV / MONITOR DC OPERATION WITH REMOTE CONTROL AVT-988 OPERATING INSTRUCTIONS SPECIFICALLY DESIGNED FOR THE VAN AND RV INDUSTRIES RECOMMENDED GUIDELINES FOR THE USE OF A VIDEO MONITOR IN A MOTOR VEHICLE · A VIDEO MONITOR / TV is designed for rear passenger viewing only. This product may only be installed in the rear seat compartment of the vehicle, out of the driver's view. · Installation in any other area of the vehicle, including anywhere within the driver's view, is illegal in most states, provinces and countries and may lead to driver distraction resulting in an accident, injury and or death. If you are unsure of regulations regarding this, please consult your local laws to determine how this applies to you. Users should be aware of possible noise distraction caused by the use of the product and should carefully monitor the volume so as not to interfere with the driver's attention to surrounding traffic conditions. · EXPLANATION OF GRAPHIC SYMBOLS: CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. [. . . ] µ External Speaker Jack · You can plug an optional External Speaker into this jack for private listening. · If an external speaker is connected, the sound will come through the external speaker instead of the TV speaker. 11 AUDIO / VIDEO Input Jack · Use an audio/video cable to connect this jack to the audio/video output from a video camera, VCR, video game, etc. · The jacks on the rear are for audio and video input IN "VIDEO 1" mode. 12 ANTENNA Jack · Connect the antenna cable to the VHF-UHF antenna terminal. - 5­ BATTERY INSTALLATION Before attempting to operate your Remote Control, install the batteries as described below. Slide the cover back until it clicks. - 6­ REMOTE CONTROL OPERATION 1. Direct Access (0-9, 1--) Number Buttons Use these buttons to select a channel. The channel number chosen will be displayed on the screen for about four seconds. To select channels above 100, press the 1--button, then the number buttons for the last two digits of the channel. CHANNEL s /t Buttons t Use these buttons to advance to the next higher (s) or lower (t) channel. Volume +/- Buttons Use these buttons to raise (+) or lower (-) the TV sound level (also used to make picture adjustments in picture selector mode). - 7­ 5. Use s and t buttons to select desired function, then press ENTER button to end the choice. TV/VIDEO Button Press this button to access the AUDIO/VIDEO input jacks, on the front and rear of the TV. As the button is pressed, the on-screen display will cycle as follows: TV VIDEO 1 VIDEO 2 7. ERASE / ADD Button This button is used to manually add or erase any channel that is stored in the CHANNEL s / t memory. The stored channel numbers are displayed in GREEN on the screen and the non-stored channel numbers are in RED. TV / CATV Button Use this button to select regular 69-channel broadcast TV or 125-channel cable TV (standard cable, HRH cable, or IRC cable). AS the button is pressed, the on-screen display will cycle as follows: AIR CABLE-S CABLE-H CABLE -I - 8­ 10. AUTO PROGRAM Button Select the regular channel broadcast TV or CABLE TV for AUTO PROGRAM. When the AUTO PROGRAM button is pressed, the TV screen will show an IMPORTANT information screen, all the channel numbers for TV or CABLE TV will be scanned. The broadcasting signals will be detected and automatically stored. IMPORTANT Reception on any TV in a mobile environment may be affected by: Vehicle movement, weather, distance from TV station, etc. These factors may cause the picture to roll, be snowy, and cause some color loss. [. . . ] Approval of antenna performance and application, should not be given without adequate testing in both VHF and UHF areas. -18- TECHNICAL INFORMATION The following information will discuss DC power sources and how they affect 12 volt DC Audio and Video products. DC (DIRECT CURRENT) POWER A large number of our products are designed for 12 volt DC applications. The power is supplied by a variety of sources i. e. , the battery, converters, ignition systems and solar power. General Specifications Our general specification for the voltage range of operation is 10 to 16 volts DC. TV's and VCP's (video cassette players) require slightly more than 10 volts to function properly. [. . . ]