User manual AUDIOVOX AVT-1928

[. . . ] UDIOVOX PECIALIZED PPLICATIONS, L. L. C. INSTRUCTION MANUAL 19" COLOR TELEVISION AVT-1928 The serial number is located on the rear of the set. Serial No. _________________________________ CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to important operating and servicing instructions in the literature accompanying the appliance. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). [. . . ] If you connected an antenna to your TV, select AIR; if you connected a cable system, select CABLE. Use the CH buttons to select AUTO PROGRAM, then use the VOL button to begin the AUTO PROGRAM process. You will not need to reprogram the memory unless you change the type of cable or antenna connected to your TV. Chapter 3: Operating your TV-10 Changing Channels You can change channels in three ways: 1. The Ch buttons will not access channels that have not been programmed into the TV's memory. For more information about programming channels into memory, see the section "Programming your TV's Channel Memory, " above. The number buttons (0-9) will take you to any channel, even if it has not been memorized. To change to a channel, enter it's number; the TV will tune to the new channel when you enter the second digit of the channel. The PREV. CH button will take you instantly to the last channel you were watching. To change the volume of the TV set, use the VOL buttons on the remote or on the front panel. Changing the TV's Channel Memory Your TV's memory determines the channels that are available using the CH buttons. If a channel is removed from memory, you can tune to it with the number buttons, but you cannot tune to it with the CH buttons. 1. The channel will turn from magenta to green to show it has been added. Chapter 3: Operating Your TV-11 Erasing a channel from memory 1. The channel will turn from green to magenta to show it has been erased. Changing the TV's channel memory with the menus You can also use the menu system to add/erase channels from memory: 1. If the channel is in memory, it will be labeled "ADD", and the number in the corner will be green. If the channel is not in memory, it will be labeled "ERASE", and the number in the corner will be magenta. Wait 7 seconds, or press MENU twice to exit. Displaying the Current Channel 1. The current channel will be displayed briefly. 12- Chapter 3: Operating Your TV Adjusting Video Settings You may wish to adjust the video settings (e. g. Use the VOL buttons to adjust the video setting to the level you prefer. When you are finished, press the MENU button twice to return to normal viewing. Chapter 3: Operating Your TV- 13 Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps: 1. Complete steps 1-3 in the "Adjusting Video Settings" section, on the previous page. This will return all video settings to their default levels, as set at the factory. You can also return to the factory settings during normal TV viewing by pressing the AUTO. PICT button on the remote control. [. . . ] · Check that the antenna is connected, is in good working order, has no broken wires and is adjusted correctly. · Check that the antenna is connected, is in good working order, has no broken wires and is adjusted correctly. · Check that the antenna is connected, is in good working order, has no broken wires and is adjusted correctly. You can not tune to a cable channel · Make sure that the AIR/CABLE setting is correct. [. . . ]