User manual AUDIOVOX AVT-1498

[. . . ] 13" COLOR TV/MONITOR DC OPERATION WITH REMOTE CONTROL AVT1498 OPERATING INSTRUCTIONS SPECIALLY DESIGNED FOR THE VAN AND AUTOMOTIVE INDUSTRIES RECOMMENDED GUIDELINES FOR THE USE OF A VIDEO MONITOR/TV IN A MOTOR VEHICLE * A VIDEO MONITOR /TV is designed for rear passenger viewing only. This product may only be installed in the rear seat compartment of the vehicle, out of the driver's view. * Installation in any other area of the vehicle, including anywhere within the driver's view, is illegal in most states, provinces and countries and may lead to driver distraction resulting in an accident, injury and or death. If you are unsure of regulations regarding this, please consult your local laws to determine how this applies to you. [. . . ] 3. 4. 6 BATTERY INSTALLATION Before attempting to operate your Remote Control, install batteries as described below. The stored channel numbers are displayed in GREEN on the screen and the non-stored channel numbers are in RED. TV/CATV Button Use this button to select regular 69-channel broadcast TV or 125-channel cable TV (standard cable, HRC cable, or IRC cable). As the button is pressed, the on-screen display will cycle as follows: AIR CABLE-S CABLE-H CABLE-I 9 * REVISED DATE : 07/04/03 DRAWING CHANGE 10. AUTO PROGRAM Button Select the regular channel broadcast TV or CABLE TV for AUTO PROGRAM. When the AUTO PROGRAM button is pressed, the TV screen will show an IMPORTANT information screen, all the channel numbers for TV or CABLE TV will be scanned. The broadcasting signals will be detected and automatically stored. Reception on any TV in a mobile environment may be affected by: Vehicle movement, weather, distance from TV station, etc. . These factors may cause the picture to roll, be snowy, and cause some color loss. For the best picture quality, a VCP is recommended. IMPORTANT SCANNING AIR CH : 269 (for TV) or SCANNING CABLE CH : 1125 (for CABLE TV) 11. PICTURE SELECT Button Each time this button is pressed the on-screen picture adjustment display cycles through "adjustment screens" as follows: CONTRAST BRIGHTNESS SHARPNESS TINT COLOR Then use the VOLUME +/ buttons to raise (+) or lower () the level. The display will automatically turn off if no adjustments are made within four seconds, or if any other button is pressed. "REW" REWIND Button If this button is pushed while the tape is stopped, the tape will rewind. If this button is pushed while the tape is playing, the VCP will go into rewind search mode. For more information on search feature of the VCP, consult VCP owner's manual. PLAY Button Press this button to activate play mode while a tape is loaded into the VCP This button may also . FWD" FAST FORWARD Button If this button is pushed while the tape is stopped, tape will fast forward. If this button is pushed while the tape is playing, the VCP will go into fast forward search mode. For more information on search feature of the VCP consult the VCP owner's manual. REPLAY Button During playback, press this button to rewind the tape to the beginning and to begin PLAY mode from there. 11 ADJUSTING THE PICTURE When watching TV programs, the quality of the picture can be adjusted to suit your taste. The main menu appears. MENU MAIN MENU SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO-PROGRAM ANTENNA INPUT V-CHIP PROTECT SET PASSWORD 2. Press either CHANNEL s or t to select the function. Make sure the highlight bar is PICTURE and then press ENTER. CHANNEL MAIN MENU SELECT VIDEO CLOSED CAPTION SET PICTURE AUTO-PROGRAM ANTENNA INPUT V-CHIP PROTECT SET PASSWORD ENTER PICTURE COLOR CONTRAST BRIGHTNESS SHARPNESS TINT RESET 12 3. Select the item to adjust. For example: To adjust brightness, press CHANNEL t or s to select BRIGHTNESS and press ENTER. CHANNEL PICTURE COLOR CONTRAST BRIGHTNESS SHARPNESS TINT RESET ENTER 32 BRIGHTNESS + 4. Adjust the level: Press VOLUME "" or "+" to adjust the level. VOLUME + 50 BRIGHTNESS + 13 5. To adjust other items, repeat all above. [. . . ] Approval of antenna performance and application, should not be given without adequate testing in both VHF and UHF areas. 24 TECHNICAL INFORMATION The following information will discuss DC power sources and how they affect 12 volt DC Audio and Video products. DC (DIRECT CURRENT) POWER A large number of our products are designed for 12 volt DC applications. The power is supplied by a variety of sources i. e. , the battery, converters, ignition systems and solar power. General Specifications Our general specification for the voltage range of operation is 10 to 16 volts DC. TV's and VCP's (video cassette players) require slightly more than 10 volts to function properly. [. . . ]