User manual AUDIOVOX AOM683

[. . . ] While it will withstand short periods of exposure to moisture, this product does contain sensitive electronic components and exposure to moisture should be limited by the user / installer. This product is not designed for applications where constant exposure to moisture or immersion can be encountered. This unit should NEVER be cleaned with a power washer or used where direct power washer spray may be encountered. 2 PACKING CONTENTS: 90 DAY/ 12 MONTH LIMITED WARRANTY Audiovox Specialized Aplications, LLC (the company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of purchase, such defect(s) will be repaired or replaced (at the company's option) without charge for parts and labor repair. After the initial 90 day period and for a period of 12 months from the date of original purchase, the company will supply at no charge a replacement for any defective part(s) but will charge for the labor to repair the product. [. . . ] In stand-by mode, the unit automatically turns on only when 12V is applied to the stand-by trigger wire. For MANUAL operation, the AOM683 should be wired as follows: The ACC (+12V) lead (red) should be wired to the ACC feed of the vehicle (switched +12V). *Please note that if the unit is in "Stand-by On" mode, the Power Button will appear to have no effect (it will switch from "on" to "on" in this case). For STAND-BY operation, the AOM683 should be wired as follows: The ACC (+12V) lead (red) should be wired to the ACC feed of the vehicle (switched +12V). The stand-by reverse, left, right trigger should be wired to the ACC feed of the vehicle (+12V when the vehicle is in reverse or left signal or right signal). The unit will automatically turn ON whenever the stand-by trigger is +12V with below condition: ­ when Stand-By Reverse trigger is +12v, unit will active AV1 display image on screen. ­ when Stand-By Left trigger is +12V, unit will active AV2 display image on screen. ­ When Stand-By Right trigger is +12V, unit will active AV3 display image on screen. ­ * Note : The unit will not be turn ON during the harzard condition and the three stand-by trigger is in +12V at the same time. 4 The power button features dual-illumination (bright and dim). In installations where the unit is not wired for Stand-by operation and power is applied to the unit, the Power Button will dimly glow when the unit is off, allowing the user to easily find the control in low light. Illumination switches to full intensity when the unit is turned on. S S 2. Source Input Select Button This control toggles the active display image back and forth between AV1, AV2 or AV3 inputs. Day/Night Mode Button This control toggles the unit between "Day" and "Night" LCD illumination modes. In the "Day" mode, the LCD backlight intensity is at maximum. In "Night" mode, the LCD backlight is dimmed to a preset level that is more suitable for low light operation. Picture Adjustment Menu Button This control accesses an On-Screen-Display (OSD) menu for four LCD picture adjustments (Brightness, Contrast, Color, and Tint). The first depress of the button accesses the "Brightness" adjustment. The Volume +/- controls adjust the level, which is indicated by the bar graph at the bottom of the screen. Each consecutive depress of the Picture button accesses the adjustment screen for each picture adjustment. If no buttons are pressed within 6 seconds or controls other than the Picture and Volume buttons are pressed, the unit will exit the Picture Adjustment mode. Volume +/- Buttons This 2-button set of controls adjusts the output volume of the built-in audio speaker when the audio function is enabled *(see typical system connection diagram). Volume level is indicated by the OSD bar graph at the bottom of the screen. These buttons also serve as adjustment controls while in the Picture Adjustment Menu mode (see above section for details). [. . . ] Use the #8 self-drilling screws (included) to secure the junction box in the desired location. The junction box can also be mounted using the 2"x 4" velcro strip (included). There are 2 options for connecting the LCD monitor to the junction box. If the application is such that the monitor is in close proximity to the junction box, the AOM683 monitor can be connected directly to the junction box. [. . . ]