User manual AUDIOVOX 1287081B

[. . . ] Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions are followed. Unplug this product from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not place the product on an unstable trolley, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. [. . . ] Connect the power, the red indicator lights up, the set is in STANDBY mode. Press the POWER button on the unit's control panel or the button on the remote control to turn the set on. Turning Off With the power on, press the POWER button to turn off the set, and the set is in standby mode. * Always unplug the AC adapter from the product and power outlet when not using for a long period of time. Notes: This TV set can automatically turn off by: 1. Press the button on the remote control or SOURCE button on the set's panel to select input mode. If you want to go to TV mode, press button repeatedly to select TV mode. Press ENTER to cancel OSD. 21 Operations in TV mode Channel Preset To enter into CHANNEL SETTING menu CHANNEL SETTING Auto search Source Current Prog Skip Auto fine tune Antenna 12 ON OFF 1. Press VOL+ or VOL- button to confirm or adjust selected item. <LEFT> or <RIGHT> key to change Antenna / Cable selection Enter into CHANNEL SETTING menu and select Source item. Cable: If using Cable TV (2-125). CHANNEL SETTING Auto search Source Current Prog Skip Auto fine tune Antenna 12 ON OFF <LEFT> or <RIGHT> key to change Auto Search Please enter into CHANNEL SETTING menu and select Auto Search item. Press VOL- or VOL+ button to start Auto Search and all active programs will be memorized. Antenna Auto searching During the process of Auto Search, pressing MENU button will stop Auto Search. 28 VHFL Press <Menu> to escape Adding and skipping channels After auto search, you can add or skip channels as follows: Select a channel to be added or skipped by direct channel select buttons. CHANNEL SETTING Enter into CHANNEL SETTING menu and Auto search select Skip item. Antenna Source 12 Press VOL- or VOL+ button to select On or Current Prog ON Skip Off. Auto fine tune OFF <LEFT> or <RIGHT> key to change Skip On: To skip the current channel. Skip Off: To add the current channel. Fine tuning In area of inferior broadcast conditions where adjustment is necessary for a better picture and sound, use Fine tuning. Use 0~9 digit buttons or CH5/6 buttons to select the desired channel, then enter into CHANNEL SETTING menu and select Auto fine tune item. Press VOL+ button to select ON to activate the auto fine tune. CHANNEL SETTING Auto search Source Current Prog Skip Auto fine tune Antenna 12 ON OFF * To exit the menu, press ENTER button. <LEFT> or <RIGHT> key to change 22 Channel Select 8 Use 0-9 digit buttons Use 0-9 digit buttons to select one-digit channel number. - -5 5 Press 0-9 button Press ENTER button To select two-digit channel: - -5 Press 0-9 button Press 0-9 button -51 51 Press ENTER button To select three-digit channel: - -1 Press 0-9 button Press 0-9 button -11 Press 0-9 button 110 Note: the period of two-press should be within 3 seconds. Use CH5/6 button Press CH5 button, the channel number increases; Press CH6 button, the channel number decreases. Use previous channel button Press this button to switch between the current channel and previous channel. 23 Picture adjustment PICTURE SETTING Brightness Contrast Color Sharpness Tint <LEFT> or <RIGHT> key to change 50 50 50 50 50 Adjusting picture 1. 2. Press CH5/6 button to select item. Item Brightness Contrast Color Sharpness Tint VOLdarker weaker paler softer purplish VOL+ lighter stronger deeper sharper greenish The adjusted settings are stored in the User mode. Press the P. M button to select a picture mode according to your favorites. 4. Press P. M button to select picture mode. You can quickly select picture mode by P. M button. Adjusted settings are stored in User mode. Using STILL button You can still current screen picture by pressing STILL button on the remote. Using AUTO. ADJ button Press AUTO. ADJ button on the remote to adjust picture for best viewing. * To exit the menu, press ENTER button. 24 Sound adjustment Adjusting Sound SOUND Bass Treble Balance MTS 25 25 25 MONO <LEFT> or <RIGHT> key to change 1. Item Bass Treble Balance MTS VOLweaker weaker decreases the right channel VOL+ stronger stronger decreases the left channel MONO/SAP/STEREO Notes: !You can quickly adjust Bass and Treble by using Bass+/ Bassand Treb+/Treb- buttons on the remote. !You can quickly select audio mode by MTS MONO MONO MONO SAP STEREO (If the program is SAP) button. STEREO (If the program is STEREO) SAP (If the program is STEREO & SAP) Adjusting Volume You can use VOL+ or VOL- button to adjust volume. Press VOL+ button, the volume increase; Muting the sound If you want to mute the sound, press button on the remote. [. . . ] Now you can adjust its horizontal and vertical position to display correctly. PICTURE POSITION Horizontal Vertical <LEFT> or <RIGHT> key to change 25 25 * To exit the menu, press ENTER button. 32 Adjustment in PC mode To enter into PC mode PC Repeatedly press button on the remote control or SOURCE button on the set's panel until the screen display PC, which indicates that the set is in PC mode. PC signal format Please connect VGA input and be sure that there is VGA input signal. The signal format should be one of the follows: 640X480 @60Hz 800X600 @60Hz 1024X768 @60Hz 1280X768@60Hz We recommend you to use 1024X768 @60Hz (4:3) or 1280X768@60Hz (16:9) so that the set can obtain the best picture. Use AUTO. ADJ button When PC signal format changes or when you switch to PC mode by button, the set corrects picture automatically including frequency and phase to obtain the best display. During the process of auto correction, all buttons on the remote control and set's panel do not work until this process is finished. [. . . ]