User manual AUDIOVOX 1285893B

[. . . ] Model APS-875 Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable IMPORTANT !In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure. Reading the sections on "Manually Overriding Your System" is necessary to fully understand the procedure required to enable your vehicle in such situations. [. . . ] If the new code was accepted, the unit will report back the newly entered code, by flashing the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the new code three times with a one second pause between each code, then the system will begin arming. If the LED flash pattern reports the previously stored code, the new code was not entered correctly. The unit will not recognize a 0 (Zero), or no digit entered in any place, units or tenths. NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to "52" you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. Within 10 seconds, press and release the valet/override switch, 3 times. Within 10 seconds, begin to press and release the pushbutton switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5) Page 8 6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on. Within 10 seconds, begin to press and release the pushbutton switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2). You will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 7, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. You will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit entered in any place, units or tenths. NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. MANUALLY OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory. NOTE: If you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above. ELIMINATING THE NORMAL ARM / DISARM CHIRPS As explained earlier in the manual, you can eliminate the chirps selectively any time you arm or disarm the system simply by holding the ARM or DISARM button for two seconds. [. . . ] OPTIONAL DEVICE OUTPUT ( CHANNEL 3 ) Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lock + Trunk/Key Buttons o Lock + Option Buttons o Unlock + Trunk/Key Buttons o Unlock + Option Buttons o Trunk/Key + Option Buttons Other Transmitter button configurations are also available. Consult your installation center for other configurations not listed above that may have been programmed to operate a specific feature of your system. This security system is equipped with an output which will activate when the appropriate transmitter button is depressed for 4 seconds. Optional devices that may be connected to this channel are; o Remote Electric Trunk Release o Remote Car Starter o Remote Window Closure o Remote Garage Door Interface NOTE: In addition there may be a second optional feature connected to your system that when the same transmitter button is pressed and released 2 times within 3 seconds (double pressed), the second optional feature will activate. [. . . ]