User manual AUDIOVOX 1285851

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AUDIOVOX 1285851. We hope that this AUDIOVOX 1285851 user guide will be useful to you.


AUDIOVOX 1285851 : Download the complete user guide (98 Ko)

Manual abstract: user guide AUDIOVOX 1285851

Detailed instructions for use are in the User's Guide.

[. . . ] If the siren did not sound when arming, then the chirps have been turned off. Refer to the section on "Eliminating the Arm/Disarm Chirps" shown later in this manual. 1 2 3 SILENT ARMING - ACTIVE: 1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk. The parking lights will flash once, and the dash mounted LED will begin to flash slowly confirming the system is armed. [. . . ] If the siren did not sound upon disarm, then the chirps have been turned off. As you approach the vehicle, press and hold transmitter button 1 for two seconds. The parking lights will flash twice, and the dash mounted LED will turn off confirming that the system is disarmed. If you have the optional door lock/unlock circuit installed, the doors will unlock. If you have the optional entry illumination circuit installed, the interior light will turn on for 30 seconds or until the ignition key is switched on. Note: If the passive arming mode was selected at time of installation, the dash mounted LED will start flashing rapidly indicating that the system is rearming. If the parking lights flashed three times, and the siren chirps four times, this indicates that the alarm system had been triggered in your absence. Before turning on the ignition key, examine the dash mounted LED's flash pattern. For additional information, refer to INTRUSION WARNING SIGNALS found later in this manual. Page 3 INTRUSION WARNING SIGNAL This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. Upon disarm, the siren will chirp 4 times and the parking lights will flash 3 times. Enter the vehicle and before turning on the ignition switch, observe the LED flash pattern. If the LED flashes one time. . . pause, one time. . . pause etc. , then an intrusion attempt was made by impact or a strong vibration that the shock sensor detected. If the LED flashes two times. . . pause, two times. . . pause etc. , then an intrusion attempt was made to open the hood, trunk, or by an accessory triggering device. If the LED flashes three times. . . pause, three times. . . pause etc. , then an intrusion attempt was made to the vehicle doors. Note: The LED intrusion warning indications are stored in the system's memory and will be erased when the ignition switch is turned on. VALET/SYSTEM OVERRIDE SWITCH The valet switch allows you to temporarily by-pass all alarm functions, eliminating the need to hand your keychain transmitter to parking attendants or garage mechanics. When the system is in the valet mode, all alarm functions are by-passed, however the remote panic feature, and the optional remote door lock/unlock will remain operational. Within 10 seconds of step 2, flip the valet switch to the "on" position. The dash mounted LED will turn on solid indicating that the valet mode has successfully been entered. To return to the normal, (alarm mode), operation, move the valet switch to the "off" position any time the ignition switch is in the on position. Note: In the event that you lose your keychain transmitter or the transmitter fails to operate the alarm system, the valet switch can be used to disarm the alarm. Always remember to move the valet switch to the off position to ensure the vehicle remains protected at all times. [. . . ] Some of the more common uses for this channel are: q Remote Trunk Release q Remote Window Close q Remote Garage Door Interface To operate the accessory associated with channel 2, press and hold transmitter button 2 for four seconds. NOTE: The feature that has been added to channel 2 will always be operated using the same transmitter button that controls the remote start unit. There is no way to move the channel 2 function to a different channel. ADDITIONAL REMOTE FUNCTION CHANNEL 3 The system has an additional feature, ( Channel 3) , that can be connected to a number of different optional accessories. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AUDIOVOX 1285851




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AUDIOVOX 1285851 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.