User manual ATIKA KS 2201-40 BROCHURE

[. . . ] Do not operate machine before having read the operating instructions, understood all the notes and assembly the machine as described here. Überprüfen Sie die Kettensäge auf offensichtliche Mängel wie - lose, ausgehängte oder beschädigte Sägekette - lose Befestigung - verschlissene oder beschädigte Bauteile Überprüfen Sie die Kettensäge nach jedem Gebrauch auf - Verschleiß, insbesondere Kette, Schwert und Kettenrad. Declaration of conformity Extent of delivery Operating times Symbols on the chain saw Symbols Operating instructions Normal intended use Residual risks Security instructions - Electrical safety Assembly Before the first commissioning - Chain lubrication - Charging the oil tank Commissioning - Mains connection - Mains fuse - Electrical mains supply impedance - Switching On/Off - Chain brake - Checking of chain brake - Clamping of saw chain Working with the chain saw - Before sawing - Saw backstroke - How to avoid backstrokes - General conduct when sawing - Additional advices for sawing trunks - Additional advices for sawing timber under tension/release - Additional advices for chopping down trees Maintenance and cleaning - Maintenance - Sharpening of saw chain - Exchanging saw chain and sword - Chain wheel - Checking of the oil automatic - Cleaning Transport Storage Guarantee Technical data Possible faults Discription of chain saw / Spare parts 17 17 17 18 18 18 18 18 20 20 20 20 20 21 21 21 21 21 21 21 21 22 22 22 22 22 23 23 23 24 24 24 24 24 24 25 25 25 25 25 26 26 / 177 KG Schinkelstraße 97 59229 Ahlen - Germany declare under our sole responsibility, that the product chain saw typ KS 2001/40, KS 2201/40 to which this declaration relates corresponds to the relevant basic safety and health requirements of the Directive 98/37/EC, and to the requirements for the other relevant Directives: 2004/108/EG, 2006/95/EC. Measured sound power level LWA 104 dB (A) Guaranteed sound power level LWA 105 dB (A) After unpacking, check the contents of the box > That it is complete > Check for possible transport damage Report any damage or missing items to your dealer, supplier or the manufacturer immediately. [. . . ] Clamp the saw chain as described in paragraph , , Clamping of saw chain". Before the first commissioning Chain lubrication The chain saw is not delivered filled with saw chain adhering oil. The use without saw chain adhering oil results in damages of the chain saw. The durability and cutting power of the chain depends on the optimal lubrication. During operation the chain saw is lubricated automatically with oil via the oil flow canal. Once you have filled the oil tank for the first time or after it was completely emptied press the "primer" about 10 times to pump oil in the circuit. Replenish immediately oil when oil level indicates , , MIN" so that the saw chain does not run dry. Then, form with the extension cable a tight noose and push it through the safety web. 2 = Chain brake active Chain saw does not initiate Set the chain brake release (3) in pos. Check the saw chain tension before start of work after the first steps during sawing regularly all 10 minutes Only with a correct clamped saw chain and a sufficient lubrication you can influence the durability. When carrying out the works observe that the extension cable is always leading backwards from the chain saw, and is outside the zone of the saw chain and the sawing material. Saw backstroke is the sudden strike upwards or backwards of the running chain saw in direction of the operator. This happens when - the sword pike gets in contact with the sawing material (unintended) or other hard objects. The chain saw reacts uncontrolled and causes frequently heavy injuries with the operator. Carry out lateral cuts, diagonal cuts and longitudinal cuts with increased attention because here the claw stopper (16) is not put on. - - - - - - - - - - - - - Never try to put on the sword pike for cutting. + Make sure that the wood is free of foreign object (stones, nails etc). + Hold the chain saw always firmly with both hands, left hand on the front handhold (4) and right hand on the rear handhold (17). 16 + When sawing thicker perches or trunks set back the claw stopper (16) on a deeper point. For setting back release the claw stopper from the wood and place it again in a deeper position. + Let the chain saw work by producing a light leverage pressure over the claw stopper. + Never work - with stretched arms - on hardly accessible places - standing on a ladder, a staging or a tree. [. . . ] Necessary repair works or maintainance works have to be carried out before the usage of the chain saw. Check the function of the automatic chain lubrication by switching on the chain saw and holding it with the pike in direction of a carton or paper on the ground. If an increasing oil track is caused when checking it the oil automatic works faultless. If there is no oil track despite full oil tank clean the oil flow canal (14) and the upper chain clamping boring (15). [. . . ]