User manual ATIKA HSC 580-18 BROCHURE

[. . . ] Do not operate machine before having read the operating instructions, understood all the notes and assembly the machine as described here. Extent of delivery Operating times EC Declaration of Conformity Symbols operating manual Symbols on machine / charger / battery Normal intended use Risidual risks Safety Notes ­ General Power Tool Safety Warnings ­ Safety instructions for hedge trimmers ­ Safety notes for chargers ­ Safety instructions for the battery ­ Safe working Description of device / spare parts Before the first start-up ­ Charging the rechargeable battery Start-up ­ Switching on / off Work instructions ­ Working with the hedge trimmer ­ Vibrations Maintenance and cleaning Maintenance Cleaning Transport Storage Disposal ­ Transport Guarantee Possible faults Technical data 13 13 13 13 14 14 14 15 15 16 16 16 16 17 17 17 17 17 18 18 18 18 18 18 19 19 19 19 19 19 20 Before initiating the device please observe the provisions pertaining to corresponding laws (regional provisions) for the noise control. KG Schinkelstraße 97 59227 Ahlen ­ Germany herewith declare under our sole responsibility that the product Hedge trimmer HSC 580/18 is conform with the above mentioned EC directives as well as with the provisions of the guidelines below: 2004/108/EG, 2000/14/EG, 2006/95/EG Following harmonized standards have been applied: EN 60745-1:2006; EN 60745-2-15:2006; EN 55014-1:2006; EN 55014-2:1997+A1:2001 Conformity assessment procedure: 2000/14/EC - Appendix V. After unpacking, check the contents of the box That it is complete Check for possible transport damage Report any damage or missing items to your dealer or the manufacturer immediately. [. . . ] C) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. D) Under abusive conditions, liquid may be ejected from the battery; avoid contact. A) Have your power tool serviced by a qualified repair person using only identical replacement parts. Do not operate the charger on combustible surfaces (such as paper, textiles). There is a risk of fire as the charger heats up during the charging process. Before each use, check the charger, charger cable and cable connector for damages. Have your charger only be repaired by qualified specialized personnel with genuine spare parts. Do not continue the charging process when the battery is not fully charged after the indicated charging time has lapsed. Only charge the battery at temperatures between 10°C and 40°C. Otherwise, the battery may be damaged or its service life may be reduced. When the charger is not used disconnect it from the mains supply and store it in a dry area. Remove the battery and store it in a dry place when the power tool is not used. Do not attempt to remove cut material or to hold material to be cut while the cutting tool is in operation. A single moment of inadvertence when using the hedge shear may result in severe injury. Make sure that all protective devices and handles are attached before using the unit. Never attempt to put into service an incomplete unit or a unit that was improperly modified. Always install the guard when transporting or storing the hedge shear. A careful handling of the unit minimises the risk of injury by the cutting tool. During the work, the cable may be hidden by shrubbery and accidentally cut. This device is not intended to be used by persons (including children) with restricted physical, sensory or mental abilities or a lack of experience and/or know-how unless they are supervised by a person responsible for their safety or they have been instructed by such a person on the use of the device. Protect the battery against heat, including permanent exposure to sunlight, and fire. - Damaged or illegible safety warning labels should be replaced immediately. [. . . ] To guarantee a long and reliable usage of the product carry out the following maintainance works regularly. Check the machine for obvious defects such as - loose, hung out or damaged cutting tools - worn or damaged components - correct assembly and faultless covers and protective devices. Necessary repair works or maintainance have to be carried out before using the power tool. Clean the machine and its accessories thouroughly after each application so that the faultless function is kept. [. . . ]