User manual ATIKA BKS 45

[. . . ] Überprüfen Sie die Kettensäge auf: - lose oder beschädigte Sägekette - lose Befestigungen - Verschleiß, insbesondere Kette, Führungsschiene und Kettenrad. EC Declaration of Conformity Extent of delivery Operating times Symbols on the chain saw Symbols Operating instructions Proper use Residual risks Safety instructions - Personal protective clothing - Before sawing - Operating - While sawing - Saw backstroke - General notes - Safe handling with fuels Work instructions (saw techniques) Assembly - Installing the guide bar and the saw chain - Clamping of saw chain Preparing for startup - Chain lubrication - Filling up saw chain oil - Checking the chain lubrication - Fuelling - Mixing - Fuelling the chain saw Inbetriebnahme - Chain brake - Checking the chain brake - Before starting the chain saw - Starten bei kaltem Motor - Stoppen des Motors - Starten bei warmem Motor Start-up - Adjusting the chain lubrication - Saw chain and guide bar - Sharpening of saw chain - Cleaning the guide bar - Chain wheel - Cleaning the air filter - Replacing the fuel filter - Checking/replacing the spark plug - Checking the ignition spark - Chain catcher - Silencer/exhaust outlet - Adjusting the carburetor (idle speed) - Care Transport Storage Guarantee Maintenance and cleaning schedule Possible faults Technical data Description of device / spare parts 17 17 17 18 18 18 18 19 19 19 19 20 20 20 21 21 22 22 22 23 23 23 23 23 23 24 24 24 24 24 24 25 25 25 25 25 25 26 26 26 26 26 27 27 27 27 27 27 27 27 28 29 30 30 KG Schinkelstraße 97 59227 Ahlen - Germany declare under our sole responsibility, that the product Petrol chain saw Type BKS 45 to which this declaration relates corresponds to the relevant basic safety and health requirements of the Directive 98/37/EC, and to the requirements for the other relevant Directives: 2004/108/EG and 2000/14/EG Conformity Assessment Procedures: 2000/14 EEC ­ Appendix V Measured sound power level LWA 113, 7 dB (A). After unpacking, check the contents of the box > > That it is complete Check for possible transport damage Report any damage or missing items to your dealer, supplier or the manufacturer immediately. 1 chain saw 1 guide bar 1 saw chain 1 scabbard 1 fuel mixing can 1 round file 1 operating manual 1 assembly and operating instruction sheet 1 warranty declaration 1 assembling tools Before initiating the device please observe the provisions pertaining to corresponding laws (regional provisions) for the noise control. [. . . ] The saw chain is correctly stretched when it can be lifted in the centre of the chain guide by appr. Cut a kerf with the saw of approximately one third of the tree diameter into the trunk. First of all place the horizontal cut and then as secondly a cut from top in an angle of 45°. Shout the warning "Caution" or "Tree is falling" before starting the fell cut. Turn the chain stretching screw anti-clockwise when the saw chain is stretched too much. Check the saw chain tension: before start of work after the first steps during sawing regularly all 10 minutes Only with a correct clamped saw chain and a sufficient lubrication you can influence the durability. Please observe the following: a new saw chain must be rest retched more frequently. in case of heating of chain to operating temperature it expands and needs to be reclamped. After finishing the sawing works release tension of saw chain as in case of cooling too high tensions would emerge in the saw chain. If chain flackers or comes out of the guide clamp it again immediately. The guarantee expires when using oil which is not allowed for chain saws. Check the function of the automatic chain lubrication by switching on the chain saw and holding it with the pike in direction of a carton or paper on the ground. If an increasing oil track is caused when checking it the oil automatic works faultless. If there is no oil track despite full oil tank: Clean the oil flow channel (19). Fill the saw chain as described under "Chain lubrication" and "Fuelling". This product is operated by a mixture from regular petrol (unleaded) and two-stroke engine oil. Petrol: Octane number at least 91 ROZ unleaded + Do not fill in leaded petrol, diesel or other non-approved fuels. This may lead to severe engine damages due to increased engine temperatures. + If you frequently operate the product at high speeds, you should use petrol with a higher octane number. To JASO FC or ISO EGD specifications + Do only use two-stroke engine oil for air-cooled engines. Any use without chain saw oil may result in damage of the chain saw and guide bar. The durability and cutting power of the chain depends on the optimal lubrication. [. . . ] dispose of remainders of fuel/saw chain oil according to relevant regulations (environmentally compatible). For this reason the oil system should be flushed before a longer storing with a commercial chain saw cleaner. Operate the chain saw without installed guide bar and chain until all of the cleaner came out of the oil outlet of the chain saw. After cleaning, immerse the saw chain in an oil bath for a short time and wrap it then with oiled paper. [. . . ]