User manual ASUS Z9PR-D12

[. . . ] No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. 1 vii Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. [. . . ] Serial Port [Enabled] Allows you to enable or disable the serial port. Configuration options: [Disabled] [Enabled] Device Mode [Standard Serial Port Mode] Allows you to change the serial port mode. Configuration options: [Disabled] [Enabled] The following item appears only when you set Runtime Error Logging Support to [Enabled]. 5 Server Mgmt menu The Server Mgmt menu displays the server management status, and allows you to change the settings. The Server Mgmt menu appears only when you install ASMB card on the motherboard. 07 [Disabled] [10 minutes] [Reset] Wait for BMC response for specified timeout In PILOTII, BMC starts at the same time when BIOS starts during AC power ON. Main BMC Firmware: O/S Watchdog Timer O/S Wtd Timer Timeout O/S Wtd Timer Policy System Event Log BMC network configuration O/S Watchdog Timer [Disabled] If enabled, starts a BIOS timer which can only be shut off by Intel Management Software after the OS loads. Helps determine that the OS sucessfully loaded or follows the O/S Boot Watchdog TImer Policy. Configuration options: [Enabled] [Disabled] O/S Wtd Timer Timeout [10 minutes] Allows you to configure the length of the O/S Boot Watchdog Timer. Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes] O/S Wtd Timer Policy [Reset] Allows you to configure how the system should respond if the OS Boot Watchdog Timer expires. Server Mgmt Change this to enable or disable all features of system Event Logging during boot. Enabling/Disabling Options SEL Components Erasing Settings Erase SEL When SEL is Full [Disabled] [No] [Do Nothing] Note: All values changed here do not take effect until computer is restarted. SEL Components [Disabled] Allows you to enable or disable all features of system Event Logging during boot. The following items appears only when you set SEL Components to [Enabled]. All values changed here do not take effect until computer is restarted. Configuration options: [No] [Yes, On next reset] [Yes, On every reset] When SEL is Full [Do Nothing] Allows you to choose options for reactions to a full SEL. Unspecified option will not modify any BMC network parameters during BIOS phase BMC network configuration DM_LAN1 DM_LAN1 IP Address in BMC: DM_LAN1 Subnet Mask in BMC: DM_LAN1 Gateway Address in BMC : DM_LAN1 MAC Address in BMC: DM_LAN1 Address Source in BMC: Configuration Address source Lan1 Lan1 Lan1 Lan1 Lan1 Lan1 IP Address in BMC: Subnet Mask in BMC: Gateway Address in BMC: MAC Address in BMC: Address Source in BMC: 000. Unspecified option will not modify any BMC network parameters during BIOS phase. Configuration options: [Previous State] [Static Mode] [DHCP Mode] The following items appear only when you set Configuration Address source to [Static Mode]. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Change this to enable or disable all features of Smbios Event Logging during boot. Smbios Event Log Standard Settings Log System Boot Event [Disabled] MECI 1 METW 60 Custom Option Log OEM Codes [Enabled] Convert OEM Codes [Disabled] Note: All values changed here do not take effect until computer is restarted. Enabling/Disabling Options Smbios Event Log [Enabled] Change this to enable or disable all features of Smbios Event Logging during boot. [. . . ] You need to manually install the Intel® Rapid Storage Technology enterprise 3. The support DVD automatically displays the Drivers menu if Autorun is enabled in your computer. If Autorun is NOT enabled in your computer, browse the contents of the support DVD to locate the file ASSETUP. When the Welcome to the Setup Program appears, click Next to start the installation. [. . . ]